Tabla de contenido
Idiomas disponibles
Idiomas disponibles
•
Let all the wheels stay on the ground and keep 2
hands on the handle when you operate the product.
Keep your hands and feet away from the rotating
blades.
•
Do not tilt the product when the engine is started.
•
Be careful when you pull the product rearward.
•
Never lift up the product when the engine is started.
If you must lift the product, first stop the engine and
disconnect the ignition cable from the spark plug.
•
Do not walk rearward when you operate the product.
•
Stop the engine when you move across areas
without grass, for example paths made of gravel,
stone and asphalt.
•
Do not run with the product when the engine is
started. Always walk when you operate the product.
•
Stop the engine before you change the cutting
height. Never make adjustments with the engine
started.
•
Never let the product stay out of view with the engine
started. Stop the engine and make sure that the
cutting equipment does not rotate.
Safety instructions for operation
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
•
Personal protective equipment cannot fully prevent
injury but it decreases the degree of injury if an
accident does occur. Let your dealer help you select
the right equipment.
•
Use hearing protection if the noise level is higher
than 85 dB.
•
Use heavy-duty slip-resistant boots or shoes. Do not
use open shoes or go with bare feet.
•
Use heavy, long pants.
•
Use protective gloves when necessary, for example
when you attach, examine or clean the cutting
equipment.
Safety devices on the product
WARNING: Read the warning instructions
that follow before you use the product.
•
Do not use a product with defective safety devices.
•
Do a check of the safety devices regularly. If the
safety devices are defective, speak to your
Husqvarna service agent.
To do a check of the cutting cover
The cutting cover decreases vibrations in the product
and decreases the risk of injury from the blade.
1500 - 001 - 02.07.2020
•
Examine the cutting cover to make sure that there
are no damages such as cracks.
To do a check of the blade brake control and the start
inhibitor
The blade brake control stops the blade only and not the
engine. When the blade brake control is released, the
blade stops.
1. Start the engine.
2. Push the blade brake control in the direction of the
handlebar. The start inhibitor stops the movement.
3. Push the start inhibitor out.
4. Push the blade brake control in the direction of the
handlebar. The blade starts to rotate.
5. Release the blade brake control. If the blade does
not stop in 3 seconds, let an approved Husqvarna
service agent adjust the blade brake. (Fig. 28)
6. Make sure that the start inhibitor goes back to its
initial position.
Muffler
The muffler keeps the noise levels to a minimum and
sends the exhaust fumes away from the operator.
Do not use the product if the muffler is missing or
defective. A defective muffler increases the noise level
and the risk of fire.
WARNING: The muffler becomes very hot
during and after use and when the engine
operates at idle speed. Be careful near
flammable materials and/or fumes to prevent
fire.
To do a check of the muffler
•
Examine the muffler regularly to make sure that it is
attached correctly and not damaged.
Fuel safety
WARNING: Read the warning instructions
that follow before you use the product.
•
Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
•
If you spill fuel on your clothing, change clothing
immediately.
•
Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use soap and water to
remove the fuel.
•
Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
•
Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
11
Capítulos
Tabla de contenido
