Black and Decker LST201 Manual De Instrucciones página 33

8. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Always remove the plug from the socket before inspecting a
damaged cable. Be careful not to use your strimmer if the
cable is damaged.
Beware of flying objects.
Keep bystanders away from the cutting area.
Do not expose the appliance to rain or high humidity.
Directive 2000/14/EC guaranteed sound power.
FEATURES (Page 2)
1. Trigger
2. Lock-off button
3. Handle
4. Auxiliary handle
5. Collar (to adjust height and edge)
6. Trimmer head
7. Edge guide
8. Guard
9. Spool housing
10. 20V MAX* Battery
11. 20V MAX* Charger
ADDITIONAL SAFETY WARNING FOR
TRIMMERS/EDGERS
Warning! Cutting elements continue to rotate after the
motor is switched off.
f Always wear eye protection: Wear safety spectacles
or goggles at all times when this tool is plugged in.
f Guard: Do not use this tool without guard attached.
f Nylon line: Keep face, hands and feet clear of
rotating nylon line at all times.
f The rotating line performs a cutting function:
use care when trimming around screens and desirable
plantings.
f Keep all by -standers away: At a safe distance from
work area, especially children.
f Important warning: When being used as an Edger,
stones, pieces of metal and other objects can be
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
thrown out at high speed by the line. The tool and
guard are designed to reduce the danger. However,
the following special precautions should be taken:
f Make sure that other persons and pets are at least
Construction
100 feet (30m) away.
Earthing
Terminal
f To reduce the risk of rebound (ricochet) injury, work
Safety Alert
going awayfrom any nearby solid object such as
Symbol
wall, steps, large stone, tree, etc. Use great care
Revolutions
or Recipro- when working close to solid objects and where
cation per
necessary, do edging or trimming by hand.
minute
f Avoid accidentally starting: Don´t carry plugged-in
tool with finger on trigger.
f Do not force the tool: at a rate faster than the rate at
which it is able to cut effectively.
f Use the right tool: Do not use this tool for any job
except that for which it is intended.
f Don´t overreach: Keep proper footing and balance
at all times.
f Don´t abuse cord: Don´t yank cord from power
supply. Keep cord from heat, oil, and sharp edges.
f Damage to unit: If you strike or become entangled
with a foreign object, stop tool immediately, unplug,
check for damage and have any damage repaired
before further operation is attempted. Do not operate
with a broken hub or spool.
f Disconnect tool: When not in use, when replacing
line, or prior to cleaning.
f Avoid dangerous environmental conditions: Do
not use electric tools in damp or wet locations. Follow
all instructions in this Instruction Manual for proper
operation of your tool. Don´t use the tool in the rain.
f Do not operate portable electric tools in gaseous
or explosive atmospheres. Motors in these tools
normally spark, and the sparks might ignite fumes.
f Store idle tools indoors: When not in use, tools
should be stored indoors in a dry, locked-up place out
of reach of children.
f Ground fault circuit interrupter (GFCI) protection
should be provided on the circuits or outlets to be
used for the gardening appliance. Receptacles are
available having built in GFCI protection and may be
used for this measure of protection.
f Stay alert: Watch what you are doing. Use common
sense. Do not operate tool when you are tired.
f Maintain appliances with care: Follow instructions
in maintenance section. Inspect extension cords
periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
f Check damaged parts: Before further use of the
appliance, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect its operation. A guard
ENGLISH • 33