Safety Of Others - Black+Decker BDAG710 Traducido De Las Instrucciones Originales

English
(original instructions)
● If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel or
brush may expand in diameter due to work load and
centrifugal forces.

Safety of others

● This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
● Children should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
● Injuries caused by touching any rotating/moving parts.
● Injuries caused when changing any parts, blades
or accessories.
● Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
● Impairment of hearing.
● Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
@
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual
use of the power tool can differ from the declared
value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated. When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms, along with the date code, are
shown on the tool:
8
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear safety glasses or goggles when operating
this tool.
Wear ear protection when operating this tool
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate.
● If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Voltage drops
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected.
If the system impedance of the power supply is lower than
0.107 Ω, disturbances are unlikely to occur.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Spindle lock
3. Guard
4. Side handle
@
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (fig. A1, A2)
The tool is supplied with a guard intended for grinding
purposes only (type 27). If the unit is intended to perform
cutting off operations, a guard specific for this operation
(type 41) must be fitted. A suitable guard part numbers
N642463 (for 115 mm cutting wheel) can be obtained from
BLACK+DECKER service centres.
● Place the tool on a table, with the spindle (5) facing up.
● Align the lugs (7) with the notches (8).
● Press the guard down and rotate it clockwise to the
required position.
● Tighten the screw (6) to fix guard.
Removing
● Loosen the screw (6).
● Rotate the guard counter clockwise to align the lugs (7)
with the notches (8).
@
● Remove the guard from the tool.
Warning! Never use the tool without the guard.