Tabla de contenido
Idiomas disponibles
Idiomas disponibles
5. Install steel elbows on top end of nipples (See Figure
10). PTFE pipe thread sealant tape all threaded joints to
prevent leaks!
note: Installing elbows at this step may make it more
difficult to fill pipe (Step 7); however, they provide a positive
stop to prevent pipe from sliding through well seal and
disappearing down the well.
figure 10
6. Install ejector in well; install well seal in top of well
casing. Tighten seal bolts to form seal with casing and to
clamp nipples.
7. While holding pipes SECURELY, fill with water to make
sure that connections and check valve do not leak
(See Figure 11). Pipes should hold water. If they leak,
remove and locate leak. Remake leaking joint with PTFE
pipe thread sealant tape or retighten clamp. Repeat
installation and fill check until pipes do not leak.
performance
taBle i – models 10pl and 15pl
model 10pl
feet to
pressure in psi
Water
20
30
Gpm with J32p-24 Venturi and #51 nozzle
30
11.0
10.0
40
9.6
9.1
50
9.5
8.1
60
8.2
6.6
70
7.2
5.7
80
5.4
3.9
90
4.2
3.2
100
2.9
2.0
110
–
–
taBle ii – models 05sl and 07sl
model 05sl
feet to
pressure in psi
Water
20
30
Gpm with J32p-32 Venturi & #55 nozzle
30
15.0
11.5
40
11.7
9.0
Gpm with J32p-24 Venturi & #51 nozzle
50
8.3
6.4
60
6.8
5.0
70
5.6
4.0
80
4.0
2.5
90
–
–
1 Hp
40
50
60
20
Gpm with J32p-28 Venturi & #55 nozzle
8.4
6.6
4.8
23.5
7.2
4.5
3.6
19.0
6.1
4.5
2.7
13.0
5.0
3.3
1.9
10.0
4.1
2.5
1.0
Gpm with J32p-22 Venturi & #53 nozzle
2.9
1.5
–
2.0
0.75
–
1.0
–
–
–
–
–
1/2 Hp
40
50
20
Gpm with J32p-33 Venturi & #51 nozzle
7.0
2.5
20.0
4.5
–
16.0
Gpm with J32p-29 Venturi & #54 nozzle
4.0
2.0
11.9
3.0
1.0
8.4
Gpm with J32p-24 Venturi & #51 nozzle
1.8
–
7.2
0.75
–
5.4
–
–
4.2
8. Install adapters in elbows and connect horizontal offset
piping to pump. Connect horizontal pipe as needed.
PTFE pipe thread sealant tape all threaded joints to
prevent leaks!
figure 11
model 15pl
pressure in psi
30
40
50
19.0
13.2
9.4
14.5
9.5
7.5
9.7
8.0
6.2
8.2
6.5
4.8
8.4
7.0
5.3
3.6
6.2
5.5
4.4
2.9
5.0
4.4
3.2
1.9
3.5
3.2
2.2
1.1
2.5
2.2
1.5
–
model 07sl
3/4 Hp
pressure in psi
30
40
15.2
9.7
11.5
6.0
8.6
5.2
5.8
5.0
5.7
4.1
4.2
2.9
3.2
2.0
0.75
3
1-1/2 Hp
60
7.2
5.6
4.3
3.0
2.0
1.4
–
–
–
50
3.0
2.6
2.5
2.5
2.5
1.5
Tabla de contenido
