Festool DOMINO XL DF 700 EQ Manual De Instrucciones Original/Lista De Piezas De Repuesto página 16

DF 700 EQ
GB
X
Release the snap buttons [1-8].
X Check whether the slide
gaged correctly.
L With the two markers [1-9], you can mark
two routing depths and switch easily be-
tween them using the slide [1-7](e.g. for
asymmetric DOMINO dowel depth distri-
bution).
7.4 Setting the Fence Height
L The alignment of the clamp levers
and [1-14] can be aligned by raising the
levers. When tightened, the levers should
not protrude beyond the contact surface.
a) with selection slide
X
Loosen the clamp lever for the routing
height adjustment [5-1].
X Using the front handle
front part of the guide frame.
X
Use the selection switch to set [5-6]the
desired routing
15 mm; 20 mm;
40 mm).
X Press the front section of the guide frame
downwards as far as the stop.
X
Close the clamp lever [5-1].
b) freely selectable
X
Loosen the clamp lever for the routing
height adjustment [5-1].
X Using the front handle
front section of the guide frame.
X Pull the selection slide
stop in the direction of the motor unit.
X
Set the desired routing height
scale [5-3] by moving the front section of
the guide frame vertically.
X
Close the clamp lever[5-1].
7.5 Setting the Fence Angle
X Loosen the clamp lever for the angle ad-
justment [5-4].
X Set the desired angle:
X
using the scale
to 90°.
X locking at 0°; 22.5°; 45°; 67.5°; 90°.
X
Close the clamp lever [5-4].
Set the routing height and depth as
low as possible when mitre routing as
otherwise there is a risk that the cutter
will come out the other side.
16
[1-7] has en-
[1-12]
[5-2] raise the
height (10 mm;
25 mm; 30 mm;
[5-2] raise the
[5-6] as far as the
using the
[5-5] variable from 0°
7.6 Setting the Mortise Width
Use the adjusting lever
width of the dowel hole you intend to cut for
an adequate fit or set with 3 mm play:
Tight fitting dowel 13.5 mm + cutter diame-
ter
Dowel with lat- 16.5 mm + cutter diame-
eral play ter
You can see on the display [1-5]what dowel
hole width is selected.
7.7 Setting stop pins
Six stop pins [1-2]
side of the DOMINO joining machine.
Stop pins that are not required can be indi-
vidually engaged by exerting overpressure
and released using the button [1-13].
These serve as spacers to the cutter centre
and can be inserted at different locations -
see image [6]:
A Three possible spacings to a supply
side (1 - 2 - 3)
B Two dowel holes beside each other
from a supply side (1 - 3)
C Two dowel holes by changing the work-
piece, e.g. for cross-section cut.
7.8 Dust extraction
WARNING
Dust hazard
X
Dust can be hazardous to health. Always
work with a dust extractor.
X Always read applicable national regula-
tions before extracting hazardous dust.
At the extractor connector [1-15], a Festool
mobile dust extractor with an extraction hose
diameter of 27 mm can be connected.
7.9 Widening the contact surface
The contact surface widening device
can be used to enlarge the contact surface
when routing on the workpiece edge, thus al-
lowing safer guidance of the machine.
X
Secure the contact surface widening de-
vice using the two screws
threaded holes [7-3]of the guide frame.
The contact surfaces of the contact sur-
face widening device
[7-4] must be level.
[1-6] to adjust the
are available on the stop
[7-2] on the
[7-5] and the table
[7-1]