Ec Declaration Of Conformity; Auxiliary Handle - Würth BMH 32-XE Traducción Del Manual De Instrucciones De Servicio Original

OBJ_BUCH-820-004.book Page 17 Tuesday, August 4, 2015 3:37 PM
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
EC-Declaration of Conformity
We declare under our sole responsibility that the product
described under "Tool Specifications" complies with all appli-
cable provisions of the directives 2011/65/EU,
until 19 April 2016: 2004/108/EC, from 20 April 2016:
2014/30/EU, 2006/42/EC including their amendments
and is in conformity with the following standards:
EN 60745-1, EN 60745-2-6.
Technical file (2006/42/EC) at:
Adolf Würth GmbH & Co. KG, Abt. PCM
Reinhold-Würth-Straße 12–17
74653 Künzelsau
GERMANY
www.wuerth.de
Marcel Strobel Dr.-Ing. Siegfried Beichter
General Manager General Manager
Künzelsau: 01.08.2015

Auxiliary Handle

 Before any work on the machine itself, pull the
mains plug.
 Operate your machine only with the auxiliary
handle 10.
The auxiliary handle 10 can be set to any position for a
secure and low-fatigue working posture.
• Turn the bottom part of the auxiliary handle 10 in counter-
clockwise direction and swivel the auxiliary handle 10 to
the desired position. Then retighten the bottom part of the
auxiliary handle 10 by turning in clockwise direction.
Adjusting the Drilling Depth
(see figure A)
The required drilling depth X can be set with the depth stop
11.
• Press the button for the depth stop adjustment 9 and insert
the depth stop into the auxiliary handle 10.
• Insert the SDS-plus drilling tool to the stop into the SDS-
plus tool holder 1. Otherwise, the movability of the SDS-
plus drilling tool can lead to incorrect adjustment of the
drilling depth.
• Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with
the desired drilling depth X.
The knurled surface of the depth stop 11 must face down-
ward.
Selecting the Tool Holder
For hammer drilling, SDS-plus drilling tools that can be
inserted into the SDS-plus tool holder 1 are required.
For drilling without impact in wood, metal, ceramic and plastic
as well as for screwdriving and tapping, use non-SDS-plus
drilling tools (e. g., drill bits with cylindrical shank). A keyless
drill chuck is required for such drilling tools.
Note: Do not use tools without SDS-plus for hammer drilling
or chiselling! Tools without SDS-plus and their drill chucks are
damaged by hammer drilling or chiselling.
The SDS-plus tool holder 1 can easily be exchanged against
the quick change keyless chuck 13.
Changing the Tool Holder
Dismounting the SDS-plus Tool Holder
or the Quick change keyless chuck
(see figure B)
• Pull the lock ring of the tool holder 4 firmly in the direction
of the arrow, hold it in this position and pull off the tool
holder 1 or the keyless replacement chuck 13 toward the
front.
After removing, protect the tool holder 1 or the quick change
keyless chuck 13 against contamination. Lightly lubricate the
engaging grooves, if required.
Mounting the SDS-plus Tool Holder or
the Quick change keyless chuck
(see figure B)
 Use only model-specific original equipment
and pay attention to the number of identifica-
tion grooves .Only quick-change chucks with
two identification grooves are permitted. When
an unsuitable quick-change chuck is used, the application
tool could fall out during operation.
17