Waring Commercial MX1300XTX Manual De Instrucciones página 4

button to adjust the blending speed. The LCD will show the setting
speed and motor speed will change.
NOTE: The speed can be set from 15% to 100%. Once the
button is released, the motor will shut off and the blender will to return
to standby mode. The changed pulse speed will be stored in memory to
replace the default speed at 100%.
REPROGRAMMABLE STATIONS
1. There are 4 Program Buttons for four reprogrammable beverage stations
for easy operation and consistent results. The factory-set stations are
programmed as listed below:
Liquid drinks
Frozen drinks
Ice cream drinks
Smoothies
2. To run any of the above preset programs, blender must be in
standby mode.
3. Press desired Program button to start the blender. The motor will run at
the pre-set speed within the preset blending time. The LCD will show time
remaining. Once the blender counts down to 0, the motor will stop
running and the blender will return to standby mode and prompt
PRESS ANY BUTTON TO BLEND.
NOTE: To terminate a blending program, simply press Start/Stop
button or any of the program buttons. After doing this, the blender will
return to standby mode and LCD will prompt PRESS ANY BUTTON
TO BLEND.
REPROGRAMMING BEVERAGE STATIONS
Users can add 4 new programs to meet their needs. A program can
consist of several sections, each with a different speed and running time.
For example, can be replaced with a new program that has 3 sections,
as shown below:
Section 1: speed = 75%, time = 30 seconds
Section 2: speed = 100%, time = 20 seconds
Section 3: speed = 50%, time = 20 seconds
The program has the following limitations:
Speed: 15% to 100%
Time: 5 to 90 seconds
Total running time in a program cannot exceed 90 seconds, i.e., sum
of the Sections cannot be longer than 90 seconds.
Pulse
6
NOTE: The
button will act as the enter key to proceed to next step
during the reprogramming process.
1. To enter new program, press both Speed Up
buttons simultaneously while unit is in standby mode. The blender will
enter new programming mode and the LCD will prompt ADD NEW
PROGRAM.
2. Next, you will need to set values. Press the Program button you want
to replace (i.e., 1... 4). The LCD will prompt USE UP/DOWN TO SET
SPEED: 25%.
NOTE: 25% is the default speed setting in the reprogramming mode.
3. Press Speed Up or Speed Down
The increment is 1% (150 RPMs). Press and hold the button to quickly
scroll through speeds. The speed can be set between 15% and 100%.
4. Once required speed is reached, press
to confirm setting. The LCD will now prompt USE UP/DOWN TO SET
TIME 5. NOTE: Five seconds is the default time setting in the
reprogramming mode.
5. Use Speed Up or Speed Down
to 90 seconds). Once the 90 seconds is reached, pressing Speed Up
will not increase the value and the LCD will prompt MEMORY LIMIT for
2 seconds.
6. Press button or wait 5 seconds to confirm the setting. When the
blending time is confirmed, the LCD will prompt SELECT ANOTHER
SPEED. Repeat steps 3-5 if additional processing is needed.
NOTE: When pressing Speed Up
speed for next section, the LCD will prompt USE UP & DOWN TO SET
SPEED: 25%.
7. To save the new program settings, press both Speed Up
Down buttons simultaneously. The LCD will prompt NEW PROGRAM
(PROG #) SAVED for 5 seconds. The blender will return to standby mode
and the LCD will prompt PRESS ANY BUTTON TO BLEND.
NOTE: If no button is pressed for 60 seconds when prompted to ADD
NEW PROGRAM, the blender will exit new programming mode and will
return to standby mode. The new program will not be stored.
8. To run new programs, simply press the desired Program button and the
blender will run the program set by the user. The LCD will display NEW
PROGRAM # and will count down the set time.
and Speed Down
button to set the speed value.
button or wait 5 seconds
button to set the time value (up
or Speed Down buttons to set
and Speed
7