Residual Risks - DeWalt DW745 Traducido De Las Instrucciones Originales

E N G L I S H
7 Do not overreach
Keep proper footing and balance at all times.
8 Stay alert
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired.
9 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees
both hands to operate the tool.
10 Connect dust extraction equipment
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly
used.
11 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from
the tool before operating the tool.
12 Extension cables
Before use, inspect the extension cable and replace if damaged.
When using the tool outdoors, only use extension cables intended for
outdoor use and marked accordingly.
13 Use appropriate tool
The intended use is described in this instruction manual. Do not force
small tools or attachments to do the job of a heavy-duty tool. The tool
will do the job better and safer at the rate for which it was intended.
Do not force the tool.
Warning! The use of any accessory or attachment or performance of
any operation with this tool other than those recommended in this
instruction manual may present a risk of personal injury.
14 Check for damaged parts
Before use, carefully check the tool and mains cable for damage.
Check for misalignment and seizure of moving parts, breakage of
parts, damage to guards and switches and any other conditions that
may affect its operation. Ensure that the tool will operate properly
and perform its intended function. Do not use the tool if any part is
damaged or defective. Do not use the tool if the switch does not turn
it on and off. Have any damaged or defective parts replaced by an
authorised D WALT repair agent. Never attempt any repairs yourself.
E
15 Unplug tool
Switch off and wait for the tool to come to a complete standstill
before leaving it unattended. Unplug the tool when not in use,
before changing any parts of the tools, accessories or attachments
and before servicing.
16 Avoid unintentional starting
Be sure that the tool is switched off before plugging in.
17 Do not abuse cord
Never pull the cord to disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
18 Store idle tools
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
19 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Keep all handles and switches dry, clean and free from
oil and grease.
20 Repairs
This tool is in accordance with the relevant safety regulations. Have
your tool repaired by an authorised D
should only be carried out by qualifi ed persons using original spare
parts; otherwise this may result in considerable danger to the user.
Additional safety rules for saw benches
• Do not use saw blades with a body thickness greater or a width of
tooth smaller than the thickness of the riving knife.
• Make sure that the blade rotates in the correct direction and that the
teeth are pointing to the front of the saw bench.
20
WALT repair agent. Repairs
E
• Be sure all clamp handles are tight before starting any operation.
• Be sure all blade and fl anges are clean and the recessed sides of the
collar are against the blade. Tighten the arbor nut securely.
• Keep the saw blade sharp and properly set.
• Make sure that the riving knife is adjusted to the correct distance
from the blade - maximum 5 mm.
• Never operate the saw without the upper and lower guards in place.
• Keep your hands out of the path of the saw blade.
• Disconnect the saw from the mains supply before changing blades or
carrying out maintenance.
• Use a push stick at all times, and ensure that you do not place hands
closer than 150 mm from the saw blade while cutting.
• Do not attempt to operate on anything but the designated voltage.
• Do not apply lubricants to the blade when it is running.
• Do not reach around behind the saw blade.
• Always keep the push stick in its place when not in use.
• Do not stand on top of the unit.
• During transportation make sure that the upper part of the saw blade
is covered, e.g. by the guard.
• Do not use the guard for handling or transportation.
• Immediately replace the table insert when worn or damaged.
• Check that the workpiece is properly supported. Always provide
additional support for long workpieces.
• Do not exert side pressure on the saw blade.
• Never cut light alloy. The machine is not designed for this application.
• Do not use abrasive disc or diamond cutting wheels
• Rebating, slotting or grooving is not allowed.
• In case of an accident or machine failure, immediately switch the
machine off and pull the plug. Report the failure and mark the
machine in suitable form which prevents that other persons use the
defective machine.
• When the saw blade is blocked due to abnormal feed force during
cutting, ALWAYS switch the machine off and disconnect from power
supply. Remove the workpiece and ensure that the saw blade runs
free. Turn the machine on and start a new cutting operation with
reduced feed force.
• Pull the plug from the socket when blade change or any maintenance
is needed.
• Wear always hear protection.
• Wear always safety glasses
• Wear always dust mask when sawing wood.
Saw blades
• The max. allowable speed of the saw blade must always be equal to or
greater than the no-load speed of the tool specifi ed on the nameplate.
• Do not use saw blades that do not conform to the dimensions stated
in the technical data. Do not use any spacers to make a blade fi t onto
the spindle. Use only the blades specifi ed in this manual, complying
with EN 847-1.
• Consider applying specially designed noise-reduction blades.
• Do not use HSS blades.
• Do not use cracked or damaged saw blades.
• Always choose a suitable saw blade for your application.
• Always wear gloves for handling saw blades and rough material.
Saw blades should be carried in a holder wherever practicable.

Residual risks

The following risks are inherent to the use of saws:
- injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.