Assembly Instructions; Battery Backup Assembly Instructions; Powerreclinexr + & Powerreclinexrw+ Instructions; Powerreclinexr + & Powerreclinexrw - La-Z-Boy PowerReclineXR+ Manual Del Usuario

Ocultar thumbs

Tabla de contenido

Idiomas disponibles

PowerReclineXR

Operating Instructions

Press and hold the

button down to return

the back to the upright

position. Release the

button to stop the back

in any reclined position

or when fully raised.

Press and hold the

button down to close

the legrest and return

the chair body. Release

the button to stop the

legrest in any extended

position or when

fully closed.

Press and hold the

button down to raise

the back and close the

legrest and return the

chair body. Release

the button to stop the

chair in any position or

when the back is fully

raised and the legrest

is fully closed.

Press and hold the

button down to return

the headrest. Release

the button to stop the

headrest in any position

or when fully retracted.

Press and hold the button down

to decrease the lumbar intensity.

Release the button to stop the lumbar

in any position or when fully retracted.

WARNING

– To reduce the risk of serious injury:

• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand has

been dropped in water or any liquid. Contact your La-Z-Boy

+ & PowerReclineXRw +

Press and hold the

button down to recline

the chair back. Release

the button to stop the

back in any reclined

position or when

fully reclined.

Press and hold the

button down to extend

the legrest and tilt the

chair body backward.

Release the button to

stop the legrest in any

extended position or

when fully raised.

Press and hold the

button down to recline

the back, extend

the legrest and tilt the

chair body backward.

Release the button to

stop the chair in any

position or when the

back is fully reclined

and the legrest is

fully raised.

Press and hold the

button down to rotate the

headrest forward. Release

the button to stop the

headrest in any position

or when fully forward.

Press and hold the button

down to increase the

lumbar intensity. Release

the button to stop the

lumbar in any position or

when fully extended.

dealer for service.

PowerReclineXR

WARNING

• Do not attempt to disassemble or service the pump or motor; no serviceable parts are

inside. Contact your La-Z-Boy

• Check the condition of the power supplies, electrical cords, plugs, and connectors often.

Keep the power supplies and electrical cords away from heat sources. Never operate

the unit with a damaged power supply, electrical cord, plug or connector. Contact your

La-Z-Boy

• The PowerReclineXR

exceeding 300 pounds per seat. Do not operate an individual seat with more than one

occupant in or on any part of the individual seat.

Troubleshooting for Legrest Operation

If the legrest stops moving while closing, it may have encountered an obstruction.

1. Check to make sure there are no obstructions. Lift and hold the legrest up, look for obstructions

and remove them.

2. The legrest uses spring tension to close, and will close quickly when the obstruction is removed.

Release the legrest slowly to prevent it from slamming shut.

Troubleshooting for PowerReclineXR

1. Make sure the 120 volt power cord is plugged into an electrical outlet.

2. Check the power supply to make sure the green LED power indicator light is on.

3. Make sure the electrical outlet is working. For example, make sure there are no blown

fuses or tripped circuit breakers.

4. Make sure all the connectors are secure; refer to the Assembly Instructions.

5. Make sure the electrical cords are not crimped or pinched. Make sure the electric cord

or plug is not damaged.

6. Make sure the operating capacity has not been exceeded and there is only one occupant

in the individual seat or unit; refer to the Operating Instructions.

Power Supply Replacement

If the power supply must be replaced:

1. Unplug the power supply from the electrical outlet.

2. Unplug the 120 volt power cord from the electrical outlet and disconnect the power supply from

either the Y-cable or motor connector, whichever comes with the product.

3. Connect the new power supply to the motor connector or (Y-cable), and close the locking cover

when applicable. Connect the 120 volt power cord to the new power supply; refer to the