Powerreclinexr + & Powerreclinexrw+ Instructions - La-Z-Boy PowerReclineXR+ Manual Del Usuario

PowerReclineXR
ssembly Instructions
NOTICE:
-- Do not plug in until instructed.
1. Carefully cut the plastic tie holding the power supply box and the hand wand to the
body bracket (F 1).
IGURE
2. Remove the power supply from the box and the hand wand from the bubble wrap.
Lay the hand wand on the seat.
WARNING
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
• The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
3. Make back electrical connections.
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
•
attached to the back (one on each side), to 45° from vertical (F
Locate and identify the two electrical connections between the back and the body.
•
The blue connectors on the left side (sitting) are for the adjustable headrest feature.
-
One connector routes from bottom of the back panel and the other between the rear
seat and tailgate.
- The gray connectors on the right side (sitting) are for the adjustable lumbar feature.
One connector routes from bottom of the back panel and the other between
the rear seat and tailgate.
• Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.
Connect the adjustable headrest (F
•
IGURE
push the connectors together and close the locking cover to secure the connection.
Connect the adjustable lumbar (F
• IGURE
push the connectors together and close the locking cover to secure the connection.
4. Install the back.
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
•
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (F 2)
IGURE
Lower the back onto the body, making sure the back and body brackets are completely engaged.
•
To make sure the back is properly installed with both sets of back and body brackets
-
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (F
the steps above.
If you are unable to install the back properly, contact your La-Z-Boy
-
Lock the brackets by using a screwdriver to push down the locking levers (F
•
5. Locate the motor connector behind the unit. Connect the motor connector to the power supply. Align
the connectors, push together until seated and close the locking cover to secure the connection (F
6. Connect the 120 volt power cord to the power supply (F
instructed in the operating instructions.
7. Proceed to the Battery Backup Assembly Instructions.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the
power supply from the power cord behind the unit. Reverse the Assembly Instructions steps. When
lifting the back up from the body, to lay across the arms, make sure to do so slowly and carefully
to prevent damage to the electrical connections.
8
+ & PowerReclineXRw +
®
4).
IGURE
5). Align the pins and sockets in the blue connectors,
5). Align the pins and sockets in the gray connectors,
3). Remove the back and repeat
IGURE
® dealer for assistance.
4).
IGURE
6). Do not plug in until
IGURE
PowerReclineXR
TM
F
IGURE
Hand Plastic
Wand Tie
F
IGURE
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
F
IGURE
6).
IGURE
Adjustable Headrest
Connection (Blue)
+ & PowerReclineXRw +
®
ssembly Instructions
Reclina-Rocker Style Featured
1 F
IGURE
Body
Bracket
Power
Supply Box
3 F
IGURE
Back
Bracket
Adjustable Lumbar
5 F
Connection (Gray) IGURE
120 Volt Power Cord
Tailgate Rear Seat
TM
2
Back Bracket
4
Locking
Lever
at 45
Degrees
from
Vertical
Locked
Position
6
Motor Connector
Make this
connection
Make this
connection
Power Supply*
*Power supplies/connections
may vary by date of manufacture.
9