Dremel 800 Manual De Instrucciones página 14

6971 Dremel Manual 800 11.11.2003 18:03 Uhr Seite 14
It is this high speed, along with its compact size and
wide variety of special accessories and attachments that
makes your Cordless Rotary Tool different from other
power tools. The speed enables it to do jobs low speed
Read the next sections carefully. They will help you use
your Cordless Rotary Tool correctly and help you select
the correct accessory for your job.
Charging the Tool
The Cordless Rotary Tool is not fully charged. The tool
is equipped with a removable battery pack. Be sure to
charge pack prior to initial use.
To charge the tool:
1. Put the switch in the "OFF" position.
2. Squeeze release tabs on both sides of battery pack,
and remove pack from back of tool as shown on page 2.
3. Align exterior shape of battery pack with exterior
shape of charger (alignment arrows on battery columm
will point to the two arrows located on charger),
Important Charging Notes
1. The battery pack accepts only about 80% of its
maximum capacity with its first few charge cycles.
However, after the first few charge cycles, the battery
will charge to full capacity.
2. The charger was designed to fast charge the bat-
tery only when the battery temperature is between
40˚F (4˚C) and 105˚F (41˚C).
3. A substantial drop in operating time per charge
may mean that the battery pack is nearing the end of
its life and should be replaced.
4. If battery does not charge properly:
Using the Cordless Rotary Tool
The first step in learning to use the Cordless Rotary Tool
is to get the "feel" of it. Hold it in your hand and feel its
weight and balance. Feel the taper of the housing. This
taper permits the tool to be grasped much like a pen or
pencil.
When you turn on the tool for the first time, hold it away
from your face. Accessories can be damaged during
handling, and can fly apart as they come up to speed.
This is not common, but it does happen.
Practice on scrap materials first to see how the Cordless
Rotary Tool cuts. Keep in mind that the work is done by
tools cannot do, such as cutting hardened steel, en-
graving glass, etc.
Getting the most out of your Cordless Rotary Tool is a
matter of learning how to let this speed work for you.
squeeze release tabs, insert battery pack into charger as
shown and release pressure on tabs so it locks in place.
4. Plug charger into the power source. The green LED
light indicates connection has been made and the
battery pack is charging. Under normal usage the tool
normally requires 3 hours charging time to reach full
capacity. When charging is complete, LED on charger
will turn off.
5. When charging is completed, squeeze release tabs on
battery pack and remove pack from charger.
6. Align exterior shape of battery pack with exterior
shape of the housing of tool as shown. Squeeze release
tabs, insert battery pack into back of tool, and release
pressure on tabs so it locks in place.
a. Check for voltage at outlet by plugging in
some other electrical device.
b. Check to see if outlet is connected to a light
switch which turns power "off" when lights are
turned off.
c. Check battery pack terminals for dirt. Clean
with cotton swab and alcohol if necessary.
d. If you still do not get proper charging, take or
send tool, battery pack and charger to your
Dremel Service Centre.
Note: Use of chargers or battery packs not sold by
Dremel may void the warranty.
the speed of the tool and by the accessory in the collet.
You should not lean on or push the tool into the work.
Instead, lower the spinning accessory lightly to the
work and allow it to touch the point at which you want
cutting (or sanding or etching, etc.) to begin. Con-
centrate on guiding the tool over the work using very lit-
tle pressure from your hand. Allow the accessory to do
the work.
Usually, it is best to make a series of passes with the
tool rather than attempt to do all the work in one pass.
To make a cut, for example, pass the tool back and forth
over the work, much as you would a small paint brush.
14 14 14