Advance BA 5321 Instrucciones De Utilizacion página 19

NAMEPLATE
The Model and Serial Number of your machine are shown on
the nameplate on the machine. This information is needed
when ordering repair parts for the machine. Use the space
below to note the Model and Serial Number of your machine
for future reference.
MODEL ..........................................................................................
SERIAL
NUMBER........................................................................................
PREPARE THE MACHINE FOR USE
(B) INSTALLING THE BATTERIES
WARNING!
Use extreme caution when working with batteries. Sulfuric
acid in batteries can cause severe injury if allowed to contact
the skin or eyes. Explosive hydrogen gas is vented from the
batteries through openings in the battery caps. This gas can
be ignited by any electrical arc, spark or flame.
WHEN SERVICING BATTERIES...
• Remove all jewelry
• Do not smoke
• Wear safety glasses
• Work in a well ventilated area
• Do not allow tools to touch more than one battery terminal
at a time
CAUTION!
Electrical components can be severely damaged if the
batteries are not installed and connected properly. Batteries
should be installed only by qualified personal.
Adjust the built-in battery charger (optional) to the type of
batteries used (wet or maintenance free types).
1. Inspect the batteries prior installation for damage.
2. Disconnect the battery connector / charger plug.
3. Carefully lift the batteries into the battery compartment
and arrange them exactly as shown on page 2.
4. Make sure that the cables from the charger plug are
conneced in the right sequence to the battery terminals.
5. Install the battery terminal covers provided with the
machine.
6. Connect the battery connector/charger plug.
(C) INSTALLING THE BRUSH
OR PAD HOLDER
WARNING!
Moving parts - disconnect the power supply connection from
the batteries before servicing.
IMPORTANT!
1. If using a pad, install the pad on the pad holder first.
2. Raise the brush deck in the upper position.
3. Place brush/padholder under the raised brush deck.
4. Lower the brush pedal.
5. Touch the drive panel quickly so that the brush/padholder
is engaged.
(D) INSTALL THE SQUEEGEE
1. Install the squeegee assembly onto the squeegee bracket.
2. Tighten the thumb nuts securely.
3. Attach the squeegee hose to the squeegee assembly.
(E) FILL THE SOLUTION TANK
1. Fill the solution tank with cleaning solution appropiate for
the job.
2. Do not overfill the solution tank
3. Always follow the dilution instructions on the chemical
container label.
4. The temperature of the cleaning solution must not exceed
40° C (100° F).
CAUTION!
Use only low-foaming, non-flammable liquid detergents
intended for automatic scrubber applications.
(F) WET SCRUBBING
1. Lower the squeegee assembly.
2. Lower the brush/pad by pushing the foot pedal.
3. Position the solution flow control lever in the required
position.
4. Turn the master key switch*; brush switch and vacuum
switch "ON". The solution will not come ON unless the
brush switch is ON.
5. Adjust the required working speed at the potentiometer*.
6. Grip the operator handle bar and push the drive panel.
• Push drive panel forward = machine moves forward
• Pull drive panel in reverse = machine moves in reverse
7. For best results, work at a slow walking speed or make a
double scrub action.
* (BA 5321 with drive motor only)
CAUTION!
To avoid damaging the floor, the brush motor is automatically
switched OFF when standing on the spot.
8. An automatic float shut-off blocks the vacuum system
when the recovery tank is full. The machine will not pick
up water with the float closed.
9. Move the machine to a designated "DISPOSAL SITE".
Empty the recovery tank via the drain hose. Rinse the tank
afterwards with clean water.
NOTE: Turn the brush switch OFF before raising the brush.
(G) TRACTION CONTROL
The forward traction can be adjusted with two set screws on
the brush deck according to floor conditions and used brush
or pad.
• Turn set screw on the
centre counterclockwise
• Turn left hand set screw
clockwise
(H) AFTER USE
1. Turn brush and vacuum switch OFF.
2. Raise the brush/padholder and the squeegee.
3. Empty solution & recovery tank into a designated
"DISPOSAL SITE" and rinse with clean water.
19
= Machine moves to the left
= Machine moves to the right