Idiomas disponibles
Idiomas disponibles
5
Turn the Groomer ON (fig. 5).
6
To trim in the most effective way, move the
Groomer slowly against the direction of hair
growth (fig. 6). Make sure the surface of the
comb always stays in contact with the skin.
NOTE: Since all hairs do not grow in the same
direction, you may want to try different trimming
positions (i.e., upwards, downwards, or across).
Practice is best for optimum results.
If a lot of hair has accumulated in the comb,
remove the comb and blow and/or shake the
hair out of the comb.
REMEMBER: You must reset the hair length
setting selector back to your desired setting
every time you replace the comb on the
appliance.
The length setting is equal to the hair length
that will remain after trimming.
7
Turn off Groomer (fig. 5). Rinse the comb
clean after each use.
Hair Clipping
Make sure that the appliance is fully charged
before you start clipping hair.
Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
Make sure the hair is clean and dry.
Before you begin, comb the hair in the direction
of growth (fig. 7).
To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Clipping with hair comb
1
Put the trimmer on Groomer handle (1) and
turn clockwise (2) (fig. 2).
2
Slide the hair comb into the guiding grooves
on both sides of Groomer handle (fig. 8).
3
Press the Hair Length Setting Selector (1)
and slide the comb to the desired setting (2)
(fig. 9).
The hair comb cuts hair to a length of 1/8 in -
25/32 in / 3-20mm.
4
The setting selected is shown on the back
of the Groomer.
When you are clipping for the first time, start
at the maximum clipping length setting (25/32
in/20mm) to familiarize yourself with the appliance
and prevent accidentally trimming hairs too
short. As you become familiar with the settings,
adjust the Hair Length Setting Selector to desired
trimming length. Selector will 'click' into position at
each setting.
5
Turn the Groomer ON (fig. 5).
6
Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (fig. 10).
7
Move the appliance slowly over the crown
from different directions to achieve an even
result (fig. 11).
8
Always move the appliance against the
direction of hair growth. Press lightly.
9
Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
10
Turn the Groomer off and remove the hair
comb often to blow and/or shake out hair
that has accumulated.
REMEMBER: You must reset the hair length
selector back to your desired setting every
time you replace the hair comb on the
appliance.
TIP: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
Contouring without the hair comb
Use the Groomer without a comb to clip hair
very close to the skin (3/64in./1mm) or to
contour the neckline and area around the ears.
1
Remove the hair comb by pressing the Hair
Length Setting Selector (1) and slide the
comb upwards (2). Pull comb off Groomer
(fig. 12).
Be careful when you are clipping without a comb
attachment as when the Clipper is turned on it
will remove every hair it touches.
2
To contour the hairline around the ears,
comb the hair ends over the ears.
3
Tilt the Groomer in such a way that only
one edge of the cutter blades touches the
hair ends when you shape the contours
around the ears (fig. 13).
Be careful not to trim too much. The hairline
should be close to the ear.
4
To contour the nape of the neck or
sideburns, turn the Groomer and make
downward strokes (fig. 14).
5
Move the Groomer slowly and smoothly
following the natural hairline.
Trimming your Beard & Moustache
with Beard Comb
1
Put the trimmer on Groomer handle (1) and
turn clockwise (2) (fig. 2).
2
Slide the beard comb into the guiding
grooves on both sides of the handle (fig. 15) .
3
Press the Hair Length Setting Selector (1)
and slide the comb to the desired setting (2)
(fig. 16).
The beard comb cuts hair to a length of 3/64-
23/32in / 1-18mm.
If you are trimming for the first time, start
by using the comb at the maximum trimming
length setting (23/32 in/18mm) to prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust Hair
Length Setting Selector to desired trimming
length. Selector will "click" into position at each
setting.
4
Turn the Groomer ON (fig. 5).
5
To trim in the most effective way, move
the Groomer against the direction of hair
growth. Make sure the surface of the comb
always stays in contact with the skin.
NOTE: Since all hairs do not grow in the same
direction, you may want to try different trimming
positions (i.e., upwards, downwards, or across).
Practice is best for optimum results.
If a lot of hair has accumulated in the comb,
remove the comb and blow and/or shake the
hair out of the comb.
REMEMBER: You must reset the hair length
selector back to your desired setting every time
you replace the comb on the appliance.
The remaining hair length corresponds with
the smallest distance between the cutting
blade and the spot where the comb is in contact
with the skin.
Beard Trimming Without Beard Comb
Remove comb if you are:
Defining hair lines
Trimming nape of neck
Removing single, unwanted hairs
1
Be certain the Groomer is in the OFF
position.
2
Remove the comb by pressing the Hair
Length Setting Selector (1) and slide the
comb upwards (2). Pull comb off Groomer .
3
Turn the Groomer ON (fig. 5).
4
Make well-controlled movements. Touch the
hair/skin lightly with the Groomer.
Stubble Trimming With Stubble Comb
Use the stubble comb to trim your stubble to
different lengths.
The stubble comb cuts hair to a length of 3/64
– 15/32 in. (1-12 mm).
1
Put the trimmer on Groomer handle (1) and
turn clockwise (2) (Fig. 2).
2
Slide the stubble comb into the guiding
grooves, on both sides of Groomer handle
(Fig. 17).
3
Press the Hair Length Setting Selector (1)
and slide the comb to the desired setting (2)
(Fig. 18).
Turn the Groomer ON (Fig, 5).
4
5
To trim the most effective way, move the
Groomer against the direction of hair growth.
Do not move the Groomer too fast. Make
smooth and gentle movements and make
sure the surface of the detail comb always
stays in contact with the skin.
