Tabla de contenido
Idiomas disponibles
Idiomas disponibles
DO NOT store or use the tool in locations where the
•
temperature may reach or exceed 104 °F (40 °C) (such
as outside sheds or metal buildings in summer). For
best life store tools in a cool, dry location.
NOTE: Do not store the tool with the switch locked on.
Never tape the switch in the ON position.
DO NOT incinerate the tool even if it is severely
•
damaged or is completely worn out. The battery can
explode in a fire. Toxic fumes and materials are created
when lithium‑ion batteries are burned.
If battery contents come into contact with the skin,
•
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is composed of a
mixture of liquid organic carbonates and lithium salts.
Contents of opened battery cells may cause
•
respiratory irritation. Provide fresh air. If symptoms
persist, seek medical attention.
Battery liquid may be flammable if exposed to spark
•
or flame.
Never attempt to open the tool for any reason. If the
•
tool case is cracked or damaged, do not charge. Do
not crush, drop or damage the tool. Do not use a tool or
USB cable that has received a sharp blow, been dropped,
run over or damaged in any way (e.g., pierced with a nail,
hit with a hammer, stepped on). Damaged tools should be
returned to the service center for recycling.
Storage Recommendations
The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold. Store the fully
charged tool disconnected from the USB cable.
Transportation
nOTE: Integral Li-ion tools should not be put in checked
baggage on airplanes and must be properly protected from
short circuits if they are in carry-on baggage.
Tool Disposal
This product uses a lithium-ion rechargeable and recyclable
battery. When the battery no longer holds a charge, the tool
should be recycled. The tool should not be incinerated or
placed in the trash.
The tool can be taken for disposal to an Authorized Service
Center. Some local retailers are also participating in a national
recycling program (refer to RBRC®). Call your local retailer for
details. If you bring the tool to an Authorized Service Center,
the Center will arrange to recycle the tool and its battery.
Or, contact your local municipality for proper disposal
instructions in your city/town.
Important Safety Instructions for All
Integral Battery Charging
WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery, charger
and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
•
The provided charger is not intended for any uses
other than charging BLACK+DECKER rechargeable
tools. Charging other types of tools may cause
their batteries to overheat and burst, resulting in
personal injury, property damage, fire, electric shock
or electrocution.
•
Use only with the Listed/Certified Information
Technology (computer) Equipment.
DO NOT expose charger to water, rain or snow.
•
•
Pull by the plugs rather than the cord when
disconnecting the charger. This will reduce the risk of
damage to the plugs and cord.
Make sure that the cord is located so that it will not
•
be stepped on, tripped over or otherwise subjected to
damage or stress.
When charging the tool outdoors, always provide a
•
dry location.
DO NOT use a charger with a damaged cord or plugs.
•
Have them replaced immediately.
Foreign materials of a conductive nature, such as, but
•
not limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the charger and charging
contacts.
Always unplug the charger from the power supply
•
when there is no tool attached to it.
Charging Procedure (Fig. A)
WARNING: Do not use tool while it is connected to the
USB cable.
1. Plug the charger
5
into any standard 120 Volt 60 Hz
electrical outlet.
2. Insert the micro USB plug
nOTE: Because this tool is equipped with a USB port,
it can be charged through USB ports. Ensure the cable
(Micro USB) and port are USB compliant.
3. Ensure the green charging LED
green charging LED is not illuminated, adjust tool handle
to ensure charging contacts are touching.
4. Charging is complete when the five green charging
LEDs
6
remains continuously ON. Battery can be left
charging or USB cable can be disconnnected.
5. Let the tool charge initially for at least 1 hour. After the
initial charge, your tool should be fully charged in 1 hour
from a fully discharged condition. Recharge discharged
batteries as soon as possible after use or battery life may
be greatly diminished. For longest battery life, do not
discharge batteries fully. It is recommended that the
batteries be recharged after each use.
Hot/Cold Delay
When the tool detects that the battery that is too hot or too
cold, it automatically starts a hot/cold delay, suspending
charging until the battery has reached an appropriate
temperature. The tool then automatically switches to
charging mode. This feature ensures maximum battery life.
English
7
into the charging port
4
6
is illuminated. If the
.
5
Tabla de contenido
