Main Components - CAME CHOPIN KLT Manual De Instrucciones

Key

This symbol indicates parts to read carefully.
⚠
This symbol indicates parts about safety.
☞
This symbol tells you what to say to end
users.
TX Transmitter
Shows that the operation has been
confi rmed.
Maximum time to perform the
XX
procedure
P2 programming
UP direction button
STOP button
DOWN direction button
Channel selection
Regulatory references
Came Cancelli Automatici is a company with an
ISO 9001-certifi ed quality management system
and an ISO 14001-certified environmental
management system. The product in question
complies with the following regulations: see
declaration of conformity.
Description
CHOPIN-KLT is a cabled weather unit with built-
in radio receiver for automatic management
of the moving part (awnings, shutters, blinds)
according to weather conditions. The unit can
control an electromechanical tubular motor
with wired commands or several motors with
the centralisation modules or with TX (with KLT
technology) by means of a built-in receiver.
Programming takes place using the 4 dip
switches located inside the unit and the TX.
The data and information provided in this manual are subject to change at any time without prior notice.

Any installation and operation that diff ers
from what is set out in this manual is
prohibited.
TECHNICAL DATA
Power supply 230 V AC / 50 Hz
Max. motor output with
current 6 A
Wired controls 3 V
Radio module frequency 433.92 MHz
Container protection
rating IP55
Operating temperature -20°C / +60°C
Operating time 4'
DIMENSIONS

MAIN COMPONENTS

① RESET button
②Programming button
③Sun adjustment trimmer
④Wind adjustment trimmer
⑤Dip switch
⑥Indicator LED
⑦Sun sensor terminal block
⑧Wind sensor terminal block
⑨Rain sensor terminal block
⑩Unit terminal block
⑪Power supply input and output and motor
output terminal block
⑫Power supply LED
⑬433.92 MHz radio module
⚠
Before intervening on the device, disconnect
the line voltage.
Installation
⚠
Installation must be carried out by qualifi ed
and experienced personnel in compliance
with applicable regulations.
PRELIMINARY CHECKS
• Check that the unit fi xing point is in a place
that is protected against shocks, that the
surfaces are solid, that there is suffi cient
space to insert the unit cover and that fi xing
to the surface takes place using suitable
components (screws, anchors etc);
• Prepare suitable piping and ducts for routing
the electrical cables, ensuring protection
against mechanical damage.
EQUIPMENT AND MATERIALS
SECURING AND ASSEMBLING THE CONTAINER
①Drill the pre-made holes to pass the electric
cables through
② Secure the base of the unit using suitable
screws, anchors or supports.
③ Insert the panel, sliding it into the container
guide
④ Put on the cover
Electrical connections
CABLE TYPE AND CROSS-SECTION
Connection Panel powersupply
FR0R CEI 20-22 CEI EN
Cable type
50267-2-1
Cable length
2
3G x 1mm
1 < 10 m
Cable length
2
3G x 1.5 mm
10 < 20 m
Cable length
2
3G x 2.5 mm
20 < 30 m
Connection Motor power supply
FR0R CEI 20-22 CEI
Cable type
EN 50267-2-1
Cable length
4G x 1mm 2
1 < 10 m
Cable length
4G x 1.5 mm 2
10 < 20 m
Cable length
4G x 2.5 mm 2
20 < 30 m
Connection Sun sensor
FR0R CEI 20-22 CEI
Cable type
EN 50267-2-1
Cable length
2 x 0.5 mm 2
1 < 10 m
Cable length
2
2 x 0.5 mm
10 < 20 m
Cable length
2
2 x 1 mm
20 < 30 m
Connection Wind sensor
FR0R CEI 20-22 CEI
Cable type
EN 50267-2-1
Cable length
3 x 0.5 mm 2
1 < 10 m
Cable length
3 x 0.5 mm 2
10 < 20 m
Cable length
3 x 1 mm 2
20 < 30 m
Connection Rain sensor
FR0R CEI 20-22 CEI
Cable type
EN 50267-2-1
Cable length
2
3 x 0.5 mm
1 < 10 m
Cable length
2
3 x 0.5 mm
10 < 20 m
Cable length
3 x 1 mm 2
20 < 30 m
⚠
Qualora i cavi abbiano lunghezza diversa
rispetto a quanto previsto in tabella, si
determini la sezione dei cavi sulla base
dell'effettivo assorbimento dei dispositivi
collegati e secondo le prescrizioni indicate dalla
normativa CEI EN 60204-1.
MOTOR POWER SUPPLY
C = L i g h t b l u e ( g re y ) : e l e c t r i c p o -
w e r s u p p l y n e u t r a l ( c o m m o n
for each direction of rotation);
= Yellow / green: earth connection
= Black: electric power supply phase
M
for commanding gearmotor rotation in
one direction;