Product Features - Bosch GLM 100 C Professional Manual Original

OBJ_DOKU-40116-002.fm Page 10 Thursday, March 13, 2014 10:15 AM
10 | English
Digital Laser Measure
Charger (accessory)
Charging time
Output voltage
Charging current
Protection class
A) For measurements from the rear measuring-tool edge, the operating range increases the better the laser light is reflected from the surface of the
target (dispersive, not reflective) and the brighter the laser point is with respect to the ambient brightness (indoors, twilight). For distances greater
than 80 m, we recommend using a retroreflective target plate (accessory). For distances below 20 m, a retroreflective target plate should not be used,
as it can lead to measuring errors.
B) For measurements from the rear measuring-tool edge, 100 % reflectance of the target (e.g., a white-painted wall), weak backlight and 25 °C oper-
ating temperature. Additionally, a deviation influence of ±0.05 mm/m must be taken into account.
C) For measurements from the rear measuring-tool edge, 10 – 100 % reflectance of the target, strong backlight and – 10 °C to +50 °C operating tem-
perature. Additionally, a deviation influence of ±0.29 mm/m must be taken into account.
D) For measurements with the rear side of the unit as reference, the max. measuring range is ±60°
E) After calibration at 0 ° and 90 ° with an additional grade error of ±0.01 ° /degree to 45 ° (max.).
F) In the continuous measurement function, the maximum operating temperature is +40 °C.
G) At 25 °C operating temperature
H) For a new and charged battery without display illumination, Bluetooth® and tone signal.
I) For Bluetooth® low-energy-devices, establishing a connection may not be possible, depending on model and operating system. Bluetooth® devices
must support the SPP profile.
Please observe the article number on the type plate of your battery charger. The trade names of individual battery chargers may vary.
Please observe the article number on the type plate of your measuring tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 20 on the type plate.

Product Features

The numbering of the product features shown refers to the il-
lustration of the measuring tool on the graphic page.
1 Display
2 Measuring button
3 Button for grade measurement / calibration **
4 Button for clearing the internal memory / On/Off **
5 Minus button
6 Button for result / timer function **
7 Button for measured-value list / storage of constant **
8 Button for function mode / basic settings **
9 Positioning pin
10 Button for selection of the reference level
11 Plus button
12 Button for length, area and volume measurement
13 Bluetooth® button
14 Cover, micro USB port
15 Micro USB port
16 Fixture for carrying strap
17 Reception lens
18 Laser beam outlet
19 1/4" thread
20 Serial number
21 Laser warning label
22 QR-Code (product information)
23 Charge connector*
2 609 141 158 | (13.3.14)
24 Battery charger*
25 Micro USB cable
26 Protective pouch
,
27 Measuring rail* ***
28 Locking lever for measuring rail
29 Tripod*
30 Laser viewing glasses*
31 Laser target plate*
* The accessories illustrated or described are not included as
standard delivery.
** Keep button pressed to call up the extended functions.
*** When operating the measuring tool in the measuring rail 27, da-
ta transmission is not possible.
Display Elements
a Measured-value lines
b "ERROR" indication
c Result line
d Digital vial / position of measured-value list entry
e Measured-value list indicator
f Measuring functions
Length measurement
Area/surface measurement
Volume measurement
Continuous measurement
Indirect height measurement
1
GLM 100 C
approx. 3 h
5.0 V
500 mA
/II
Bosch Power Tools