Denon AVR-2802 Instrucciones De Operación página 16

ENGLISH
Preset memory (Audio component)
• DENON components can be operated by setting the preset memory for CDR or MD. Operation is not
possible for some models, however. In this case use the learning function (see page 18) to store the
remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 19.
1
Set the slide switch to "AUDIO".
AUDIO
AVR/AVC VIDEO
2
Set the slide switch to "CDR/MD".
TAPE CDR/MD
CD MULTI
DVD TV
VDP VCR
3
Holding in the POWER button, press the button for the
components you want to set.
The LEARNED/TX LED flashes.
Combinations of Personal System Codes
"CDR/MD"
DIRECT
(DIRECT)
(POWER) DENON CDR A
ON / SOURCE
Preset codes set upon shipment from the factory.
16
START LEARNED/TX
SYSTEM CALL POWER
SET CALL OFF
DVD VDP TUNER
1 2 3
TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE
7 8 9
VCR-2/V.AUX
+10 0
VOLUME
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
1 AUDIO CD MULTI
AVR/AVC VIDEO DVD
VDP VCR
SYSTEM
SETUP
TUNING
TITLE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
STATUS
MEMORY RT
DISPLAY
USE/LEARN T.TONE MULTI
STEREO EXT.IN
(STEREO) (EXT. IN)
DENON CDR B DENON MD
Preset memory (Video component)
• DENON and other makes of components can be operated by setting the preset memory for your make of
video component. Operation is not possible for some models, however. In this case use the learning
function (see page 18) to store the remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 19.
1
Set the slide switch to "VIDEO".
AUDIO
RC-904
3
ON / SOURCE AVR/AVC VIDEO
SHIFT
CHANNEL
2
TV/VCR
Set the slide switch to the component to be
A / B
TAPE CDR/MD
CD MULTI
registered (DVD, VDP, VCR or TV). .
DISC SKIP+
DVD TV
3
( Keep the POWER button pressed in when
VDP VCR
performing steps 3 and 4
MASTER VOL.
MUTING
2
TV
SURROUND 3
PARAMETER Holding in the POWER button, press the button for the
MENU/GUIDE
corresponding manufacturer in block A. (Refer to Table 1.)
ON SCREEN
RETURN
DVD
SET UP
The LEARNED/TX LED flashes.
4
Next, while holding the POWER button, press the button for
the code in block B. (Refer to Table 1.) The operation is
completed when the button is released and the LEARNED/TX
LED lights.
5
To continue registering other components, repeat steps 2 to 4.
• This remote control unit can be used to operate components of
other manufacturers without using the learning function by
registering the manufacturer of the component as shown on Table 1.
)
Flashes
RC-904
START LEARNED/TX
SYSTEM CALL POWER 3,4
SET CALL OFF
ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
TV/DBS PHONO
4 5 6
3
VCR-1 CD CDR / TAPE CHANNEL
7
8
9
VCR-2/V.AUX
TV/VCR
+10 0
A / B
VOLUME DISC SKIP+
4
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
AUDIO CD MULTI MUTING
1
2
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI DVD
SET UP