Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

MODEL 325 AND 325- -EU HEAVY DUTY AIR NIBBLER
The 325 and 325- - EU Air Nibbler is designed for cutting cold rolled steel, plastic, tin,
aluminum, and other metals in paint and auto body shops and in sheet metal shops.
Ingersoll- -Rand is not responsible for customer modification of tools for applications
on which Ingersoll- - Rand was not consulted.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 5/16" (8 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905- - 1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig (6.2 bar/
620 kPa) maximum air pressure. Dust, corrosive
fumes and/or excessive moisture can ruin the
motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away
from blades when operating this cutter.
Blades may continue to cut briefly after throttle is
released.
The use of other than genuine Ingersoll- - Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll- - Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll- - Rand Office or Distributor.
 Ingersoll- - Rand Company 2001
Printed in U.S.A.
INSTRUCTIONS FOR
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
03533601
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll- - Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Prevent exposure and breathing of harmful dust
and particles created by power tool use:
Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- - lead from lead based paints,
- - crystalline silica from bricks and cement
and other masonry products, and
- - arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed to
filter out microscopic particles.
Form P6703
GB
Edition 7
August, 2001
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 325

  • Página 1 MODEL 325 AND 325- -EU HEAVY DUTY AIR NIBBLER The 325 and 325- - EU Air Nibbler is designed for cutting cold rolled steel, plastic, tin, aluminum, and other metals in paint and auto body shops and in sheet metal shops.
  • Página 2: Placing Tool In Service

    Maximum Material GSound Level ♦Vibrations Length Thickness (Gauge) dB (A) Level Pressure SPower 325, 325- - EU 1.36 92.3 105.3 Tested in accordance with ANSI S5.1- - 1971 at free speed ♦ Tested in accordance with ISO8662- - 10 ISO3744...
  • Página 3: Declaration Of Conformity

    (supplier’s name) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (address) declare under our sole responsibility that the product, Model 325- EU Heavy Duty Air Nibbler to which this declaration relates, is in compliance with the provisions of 98/37/EC Directives.
  • Página 4: Utilisation De L'outil

    FORTE MODÈLE 325 ET 325- -EU NOTE La grignoteuse pneumatique 325 et 325- -EU est destinée à la coupe des aciers laminés à froid, des plastiques, de l’étain, de l’aluminium et autres métaux dans les ateliers de peinture et de carrosserie automobile et dans les ateliers de chaudronnerie.
  • Página 5: Mise En Service De L'outil

    HNiveau de son ♦Niveau de totale matériau (calibre) dB (A) vibration Pression •Puissance 325, 325- - EU 1,36 92,3 105,3 Testé conformément à ANSI S5.1- - 1971 en vitesse libre ♦ Testé conformément à ISO8662- - 1 en vitesse libre ISO3744 •...
  • Página 6: Certificat De Conformité

    (nom du fournisseur Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (adresse déclarons sous notre seule responsabilité que le produit: Grignoteuse Pneumatique Série Forte Modèle 325- EU objet de ce certificat, est conforme aux prescriptions des Directives: 98/37/CE ISO8662 en observant les normes de principe suivantes: (1994 →...
  • Página 7 HOCHLEISTUNGS- -KNABBER BAUREIHE 325 UND 325- -EU HINWEIS Der Knabber der Baureihe 325 und 325- -EU dient zum Schneiden von kaltgewalztem Stahl, Kunststoff, Blech, Aluminium und anderen Metallen in Lackierereien, Autowerkstätten und in der Blechverarbeitung. Ingersoll- -Rand lehnt jede Haftung für Veränderungen an Werkzeugen ab, die ohne vorherige Rücksprache mit Ingersoll- -Rand vorgenommen werden.
  • Página 8: Technische Daten

    TECHNISCHE DATEN Modell Gewicht Gesamtlänge Maximale Materialstärke ♦Schwingungs- HSchallpegel dB (A) intensität Druck •Leistung 325, 325- - EU 1,36 92,3 105,3 Gemäß ANSI S5.1- - 1971 bei freier Drehzahl getestet ♦ Gemäß ISO8662- - 1 bei freier Drehzahl getestet ISO3744 •...
  • Página 9: Konformitätserklärung

    (Name des Herstellers) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (Adresse) erklären hiermit, gemäß unserer alleinigen Verantwortung, daß die Geräte: Hochleistungs- Knabber Baureihe 325- EU auf die sich diese Erklärung bezieht, den Richtlinien: 98/37/EG unter Anlehnung an die folgenden Grundnormen...
  • Página 10: Come Usare L'attrezzo

    MODELLO 325 E 325- -EU AVVISO La Roditrice pneumatica 325 e 325- -EU è stata progettata per il taglio di acciaio laminato a freddo, plastica, stagno, alluminio ed altri metalli in officine di verniciatura e di carrozzeria ed in officine di metalli a fogli.
  • Página 11: Messa In Servizio Dell'attrezzo

    ♦Livello di (dimensione) dB (A) vibrazione poll. Pressione •Potenza 92,3 105,3 325, 325- - EU 1,36 Collaudato secondo i criteri ANSI S5.1- - 1971 a velocità libera ♦ Collaudato secondo i criteri ISO8662- - 1 a velocità libera • ISO3744...
  • Página 12: Dichiarazione Di Conformità

    Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (indirizzo) dichiariamo sotto la nostra unica responsabilità che il prodotto: Roditirce Per Lavori Pesanti Modello 325- EU a cui si riferisce la presente dichiarazione è conforme alle normative delle direttive: 98/37/CE ISO8662 secondo i seguenti standard: (1994 →...
  • Página 13: Utilización De La Herramienta

    PARA TRABAJO PESADO NOTA La recortadora neumática 325 y 325- -EU ha sido diseñada para cortar chapa de acero laminado en frío, plástico, hojalata, aluminio y otros metales en talleres de pintura y chapa. Ingersoll- -Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll- -Rand.
  • Página 14: Etiquetas De Aviso

    ♦Nivel de del material dB(A) vibraciones pulg. Presión Presión •Potencia 325, 325- - EU 1,36 92,3 105,3 Probado en conformidad con ANSI S5.1- - 1971 a velocidad libre ♦ Probado en conformidad con ISO8662- - 1 a velocidad libre ISO3744 •...
  • Página 15: Declaración De Conformidad

    Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Recortadora Neumatic Modelo 325- EU Para Trabajo Pesado a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas:...
  • Página 16: Gebruik Van Het Gereedschap

    TYPE 325 EN 325- -EU PERSLUCHT KNABBELSCHAAR VOOR ZWAAR GEBRUIK LET WEL De 325 en 325- -EU Knabbelschaar is bedoeld voor het knippen van koudgewalst staal, kunststoffen, tin, aluminium en andere metalen in verf- - en carrosseriewerkplaatsen en in plaatmetaal verwerkende bedrijven.
  • Página 17: Ingebruikneming Van Het Gereedschap

    Totale lengte Maximum dikte ♦Trillings- - HGeluidsniveau material (gauge) dB(A) niveau inch Deuk •Vermogen 325, 325- - EU 1,36 92,3 105,3 Getest volgens ANSI S5.1- - 1971 bij brije snelheid ♦ Getest volgens ISO8662- - 1 bij brije snelheid ISO3744 •...
  • Página 18 (naam leverancier) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (adres) verklaren, onder onze uitsluitende aansprakelijkheid, dat het produkt: Type 325- EU Perslucht Knabbelschaar Voor Zwaar Gebruik waarop deze verklaring betrekking heeft overeenkomt met de bepalingen van directieven: 98/37/EG ISO8662 overeenkomstig de volgende hoofdstandaards: (1994 →...
  • Página 19 Spindle Bearing (2) ... . 107- - 110 for 325 ....107- - A40 Spindle ..... .
  • Página 20 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll--Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Ingersoll--Rand Company Fax: (31) 71 5218671 510 Hester Drive White House Ingersoll--Rand Company SA TN 37188 PO Box 3720 Alrode 1451 Tel: (615) 672 0321...

Este manual también es adecuado para:

325-eu

Tabla de contenido