Tabla de contenido
Idiomas disponibles
Idiomas disponibles
WORKING HINTS FOR YOUR
TOOL
If your power tool becomes too hot, especially when
used at low speed, set the speed to maximum and
run it with no load for 2-3 minutes to cool the motor.
Avoid prolonged usage at very low speeds. Always
keep the blade sharp.
Always ensure the workpiece is firmly held or
clamped to prevent movement.
Any movement of the material may affect the quality
of the cutting or sanding finish.
Start your tool before working and turn it off only
after you stop working.
Do not start sanding without having the sandpaper
fitted.
Do not allow the sandpaper to wear away , it will
damage the sanding pad. The guarantee does not
cover sanding pad wear and tear.Use coarse grit
paper to sand rough surfaces, medium grit for
smooth surfaces and fine grit for finishing surfaces. If
necessary, first make a test run on scrap material.
Excessive force will reduce the working efficiency
and cause motor overload. Replacing the accessory
regularly will maintain optimum working efficiency.
MAINTAIN TOOLS WITH
CARE
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional lubrication
or maintenance. There are no user serviceable parts
in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry
place. Keep the motor ventilation slots clean. Keep
all working controls free of dust. Occasionally you
may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
ENVIRONMENTAL
PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
PLUG REPLACEMENT
( UK & IRELAND ONLY )
If you need to replace the fitted plug then follow the
instructions below.
IMPORTANT
Oscillating Tool
The wires in the mains lead are colored in
accordance with the following code:
BLUE =NEUTRAL
Brown = Live
As the colors of the wires in the mains lead of this
appliance may not correspond with the colored
markings identifying the terminals in your plug,
proceed as follows. The wire which is colored blue
must be connected to the terminal which is marked
with N. The wire which is colored brown must be
connected to the terminal which is marked with L.
WARNING! Never connect live or neutral wires to
the earth terminal of the plug. Only fit an approved
13ABS1363/A plug and the correct rated fuse.
NOTE: If a moulded plug is fitted and has to be
removed take great care in disposing of the plug
and severed cable, it must be destroyed to prevent
engaging into a socket.
Connect
Blue to N
(neutral)
Outer sleeve
firmly clamped
DECLARATION OF
CONFORMITY
We,
POSITEC Germany GmbH
Konrad-Adenauer-Ufer 37 50668 Köln
Declare that the product,
Description WORX Sonicrafter
Type WX667 (6-designation of machinery,
representative of Sonicrafter)
Function Sanding, sawing, rasping, scraping,
polishing
Complies with the following Directives,
2006/42/EC, 2004/108/EC, 2011/65/EU
Standards conform to:
EN 55014-1
EN 55014-2
EN 61000-3-3 EN 60745-1
The person authorized to compile the technical file,
Name: Russell Nicholson
Address: Positec Power Tools (Europe)Ltd, PO
Box 152,Leeds,LS10 9DS,UK
Suzhou 2015/07/22
Allen Ding
Deputy Chief Engineer,Testing & Certification
13 Amp fuse approved
to BS1362
Brown L (live)
Cable grip
®
EN 61000-3-2
EN 60745-2-4
EN
9
Tabla de contenido
