Ryobi LLCDI1802 Manual De Utilización página 7

EN
FR DE ES IT
OPERATION
WARNING
Do not allow familiarity with products to make you
careless. Remember that a careless
second is sufficient to inflict serious injury.
WARNING
Always wear saf ety goggles or
with side shields when operating products. Failure
to do so could result in objects being thro
your eyes, resulting in possible serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or
not recommended can result in ser
injury.
APPLICATIONS
You may use this product for the purposes listed below:
■
Drilling in all types of wood products (lumber, plywood,
panelling, composition board, and hard board)
■
Drilling in ceramics, plastics, fiberglass, and laminates
■
Drilling in metals
■
Driving screws
■
Hammer drilling in concrete, brick, or other masonry
This product will accep t RYOBI
battery packs and RYOBI
battery packs.
BATTERY PROTECTION FEATURES
RYOBI 18 V lithium-ion batteries
features that protect the lithium-ion cells and maximiz
battery lif e. Under some
built-in features may cause the
powering to act differently f
During some application s,
signal the batter y to shut down, and cause the tool to
stop running. To reset the
trigger and resume normal operation.
NOTE: To prevent further shut
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
TO INSTALL BATTERY PACK
See Figure 2.
■
Lock the switch trigger by placing the rotation selector
in the center position.
■
Place the battery pack on the tool.
NL PT DA SV FI NO
English
fraction of a
safety glasses
wn into
accessories
ious personal
One+ 18 V lithium-ion
One+ 18 V nickel-cadmium
are designed with
operating conditions , these
battery and the tool it is
rom nickel-cadmium batteries.
the batter y electronics may
battery and tool, release the
down of the battery, avoid
RU PL CS HU RO
■
Make sure the latches on each side of the batter
pack snap into place and the batter
on the tool before beginning operation.
WARNING
Always remove battery pack from
you are assembling parts, making adjustments,
cleaning, or when not in use
pack will pre
cause serious personal injury.
TO REMOVE BATTERY PACK
See Figure 2.
■
Lock the switch trigger by placing the rotation selector
in the center position.
■
Depress the latches on the side of battery pack.
■
Remove the battery pack from the tool.
WARNING
Battery tools are always in operating condition.
Therefore, switch should
not in use or carrying at your side.
SWITCH TRIGGER
See Figure 3.
■
To turn the drill ON, depress the switch trigger.
■
To turn it OFF, release the switch trigger.
VARIABLE SPEED
The variable speeds
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
NOTE: You might hear a whistling or r
the switch during use . Do not be concer
normal part of the switch function.
ROTATION SELECTOR
e
(FORWARD/REVERSE/CENTER LOCK)
See Figure 3.
The bit rotation is
selector located above
held in normal operating position, the rotation selector
should be positioned to the left of the s
forward drilling. The drilling direction is reversed when the
selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental star
not in use.
CAUTION:
To prevent gear damage , always allow the chuck
to come to a complete stop
direction of rotation.
To stop the dr ill, release the
chuck to come to a complete stop.
2
LV LT ET HR SL SK
y pack is secured
your
. Removing battery
vent accidental starting that could
always be locked
switch trigger delivers higher speed
inging noise from
ned; this is a
reversible and is controlled by a
the switch trigger. With the drill
witch trigger
ting when
before changing
switch tr igger and allo
EL TR
y
tool when
when
f or
the
w the