ICON STRYKER RIG Manual Del Usuario página 4

B
A A
C
I
H
D
D
E
F F
STRyKER RIG :: FRONT
STRYKER RIG :: FRONT STRYKER RIG :: FRONT
G G
A. Shoulder impact protector
B. Front zipper
C. Adjustable side release buckle
D. Waist band adjustment strap with hook and loop fastener tab
E. Waistband with hook and loop fastener material
F. Forearm adjustment strap with hook and loop fastener
G. Thumb loop
04
J J
B
A
K K
C
L L
M M
D
E
F
STRyKER RIG :: bACK
STRYKER RIG :: BACK STRYKER RIG :: BACK
G
H. Chest plate
I. Plastic strap adjuster
J. Elastic loop and plastic hook support
K. Back protector attachment zipper
L. Elbow impact protector
M. Back protector - 7 plates
Wearing Instructions and Adjustment:
J J
1. Release the hook and loop fastener tabs on the waistband adjustment straps (D) by pulling outward on the tabs. Release the hook and loop fastener
material on the waistband by pulling outward on the waistband exposed right end, releasing the waistband itself (E). Release the hook and loop
K K
fastener on the forearm adjustment straps (F) by grasping the end and pulling outward. Release the front panel of the Stryker Rig by releasing the
adjustable side release buckle (C) and unzipping the front zipper (B). Pull Stryker Rig on, by inserting arms into the sleeves and thumbs through
the thumb loops at the end of the sleeves (G), letting the shoulder impact protectors (A) rest on the top of the shoulders. Make sure that the elbow
impact protectors (L) are in place over the elbows and that the sleeves of the Stryker Rig are not twisted. Make sure that the back protector (M)
is in place over the spine, and that the rear plastic plates (M) are facing away from the wearer's body.
2. Zip the front zipper (B) and reattach the adjustable side release buckle (C) by inserting the male half of the buckle into the female half. Be sure
that the side release buttons of the buckle are firmly engaged. Pull the forearm adjustment straps (F) snug and towards the inside of the forearm,
re-engage the hook and loop fastener material by pressing firmly on the loose end of the adjustment strap and onto the forearm. Reach down to
the right and left at the waist and grab the right and left ends of the waistband (E). Pull the left end of the waistband foreword and over the waist,
holding it in place while, at the same time, pulling the right end of the waistband forward and over the waist, then pulling the right end over the
L L
left end of the waistband. Re–engage the hook and loop fastener material by pressing firmly down on the right end of the waistband onto the left
end of the waistband. Reach down to the right and left of the waist again and grab the right and left waistband adjustment straps (D). Pull the left
end of the waistband adjuster tab (D) foreword and over the waist, being sure to pull it over the exposed end of the right hand end of the waistband
(E) (see diagram above). Re-engage the hook and loop fastener material by pressing the waistband adjustment strap hook and loop fastener tab
firmly onto the exposed right end of the waistband. Pull the right waistband adjuster tab foreword and over the waist. Re-engage the hook and
loop fastener by pressing the tab firmly onto the exposed hook and loop fastener material on the right waistband. Pull the loose end of the exposed
strap adjustable side release buckle (C) snug. Pull the loose end of the exposed strap of the plastic strap adjuster (I) snug.
3. Correct positioning of the shoulder impact protectors may be accomplished by adding slack or removing slack to the straps running through the
adjustable side release buckle (C) and the plastic strap adjuster (I). The waistband (D) may be adjusted by releasing the hook and loop fastener
tabs on the waistband adjustment straps (D) by pulling outward on the tabs. Releasing the hook and loop fastener material on the waistband
by pulling outward on the waistband exposed right end releasing the waistband itself (E) and then reattaching both the waistband (E) and the
waistband adjustment straps (D) as instructed in Section 2 above. When reattaching the waistband and waistband (E) and waistband adjustment
straps (D) according to the instructions in Section 2 above, adding slack to the elastic straps, makes waist larger, removing slack from the elastic
straps, makes the waist smaller. The position and movement of the elbow protectors may be adjusted using the forearm adjustment straps (F).
Release the hook and loop fastener on the forearm adjustment straps (F) by grasping the end and pulling outward. Pull the forearm adjustment
straps (F) snug and towards the inside of the forearm, re-engage the hook and loop fastener material by pressing firmly on the loose end of the
adjustment strap and onto the forearm. When reattaching the forearm adjustment straps (F) according to the instructions in Section 2 above,
adding slack to forearm adjustment straps, causes the elbow protectors to fit more loosely and removing slack from the elastic straps, causes the
elbow impact protectors to fit more snugly.
4. In all cases, confirm that the Stryker Rig and the impact protectors and back protector attached to it are in the correct position, and cover the areas
to be protected. Be sure that the garment fits snugly but not too tightly and that all adjustment straps are snug but not too tight. Confirm that
the garment movement is minimal and that wearing the garment does not prevent moving and controlling of all motorcycle controls. For maximum
05