ICON STRYKER RIG Manual Del Usuario página 3

ALL PROTECTORS
(Example)
ShOULdER ANd ELbOW
"S" type b
PROTECTORS
ShOULdER ANd ELbOW S
(Example)
PROTECTORS
bACK PROTECTOR
(Example)
bACK PROTECTOR
b
1
(Example)
bACK PROTECTOR
bACK PROTECTOR
In addition to the instructions on the mark, some coded information may appear which Icon® uses to track the product. The code may also appear
in other versions of the marking.
02
Pictogram indicating that a User Manual (Information Notice) has been provided for
this product.
Specification of the body part protected envisaged by Standard
EN 1621-1:1997 (see below)
• Type B protector dimensions are larger and are intended to cover the needs of most
motorcycle riders.
• Type A protector dimensions are smaller and are intended to cover the needs of
motorcycle riders in situations where type B protectors are considered unsuitable for
ergonomic reasons
Indicates protected area
• E for an elbow protector
• S for a shoulder protector
In accordance with EN 1621-1:1997
Specific symbol to indicate the back protector is for motorcycle use only.
Indicates the back protector type
• B for a back protector
• L for a lumbar area protector
In accordance with EN 1621-2:2003
Indication of the back protector's performance level, in compliance with EN 1621-
2:2003.
Back protector size, including the distance between the motorcyclist's waist and
shoulder so that the correct back protector can be chosen.
USE
Selecting the Correct Size:
In order to ensure you choose the correct size Stryker Rig, please see the table below:
Chart 2: Recommended Size of Stryker Rig
Recommended Size of Stryker Rig
Wearer's Waist to
Sex Wearer's Chest Girth
Shoulder Length
Male From 430 mm To 470 mm From 96.5 cm To 106.7 cm
Male From 430 mm To 470 mm From 106.7 cm To 121.9 cm
Protector Position and Fit:
Correct fit of the Stryker Rig is very important. The Stryker Rig itself and the attached impact and back protectors must fit properly. If the Stryker Rig
or the impact or back protectors do not fit properly they should not be used. For an impact protector or back protector to offer the maximum protection
possible, they must be placed on the area to be protected and they must cover the protected area effectively (see Chart 2 above). When the Stryker
Rig is worn under an Icon® motorcycle jacket, then, for the Stryker Rig and the attached impact and back protectors to be positioned correctly,
the motorcycle jacket must also be the correct size. The Stryker Rig is available in two sizes (See Chart 2, column 5 "Stryker Rig Product"). These
versions are designed to accommodate a single range of user "waist to shoulder lengths" and two ranges of "chest girths". Both Stryker Rig products
contain a back protector that may be the correct size for you based on your "waist to shoulder length" measurement (See Chart 2, column 2 "Wearer's
Waist to Shoulder Length"). In these cases, be sure to choose a Stryker Rig product, for which the back protector and the Stryker Rig itself, both fit
you correctly based on your "waist to shoulder length" and "chest girth" measurements (See Chart 2, column 3 "Wearer's Chest Girth"). In all cases,
the proper equipment has been supplied to keep the Stryker Rig and the attached impact protectors firmly in contact with the body. The Stryker Rig
must be worn under the rider's clothing to guarantee it remains in place, covering the protected area. Be sure that the Stryker Rig, when worn under
a motorcycle jacket, fits snugly but not too tightly. Confirm that garment movement is minimal. Confirm that any adjustment straps have the length
necessary to tighten and loosen, assuring correct fit.
back Protector Version Stryker Rig Product
Exterior shell with 7 plastic plates Stryker Rig Men's M/L
Exterior shell with 7 plastic plates Stryker Rig Men's XL/2XL
03