Before Operating Your Unit; For The Best Cooling Performance And Highest Energy Ef Ciency; Unit Placement - Friedrich X-Star XQ05 Manual De Instalación Y Funcionamiento

WARNING: Before operating your unit
Make sure the wiring is adequate for your unit.
If you have fuses, they should be of the time delay type. Before you install
or relocate this unit, be sure that the amperage rating of the circuit breaker
or time delay fuse does not exceed the amp rating listed in Figure 1.
DO NOT use an extension cord.
The cord provided will carry the proper amount of electrical power to the
n u ; t i n a e t x n e i s n o o c d r l i w n l . t o
Make sure that the receptacle is compatible with
the air conditioner cord plug provided.
This insures proper grounding. If you have a two prong receptacle you
will need to have it replaced with a grounded receptacle by a certi ed
electrician. The grounded receptacle should meet all national and local
codes and ordinances. Under no circumstances should you remove the
ground prong from the plug. You must use the three prong plug furnished
with the air conditioner.
Test the power cord
All Friedrich room air conditioners are shipped from the factory with a Leakage
Current Detection Interrupter (LCDI) equipped power cord. The LCDI device
meets the UL and NEC requirements for cord connected air conditioners
effective August 2004.
To test your power supply cord:
1. Plug power supply cord into a grounded 3 prong outlet.
2. Press RESET (See Figure 2).
3. Press TEST (listen for click; Reset button trips and pops out).
4. Press and release RESET (listen for click; Reset button latches and
remains in). The power supply cord is ready for operation.
NOTE: LCDI device is not intended to be used as a switch.
Once plugged in, the unit will operate normally without the need to reset
the LCDI device.
If the device fails to trip when tested or if the power supply cord is damaged, it
must be replaced with a new supply cord from the manufacturer. We recom-
mend you contact our Technical Assistance Line at (800) 541-6645 ext. 845.
To expedite service, please have your model and serial number available.
For the best cooling performance and highest energy efficiency
Keep the filter clean
Make sure that your air conditioner is always in top performing condition by
c e l n a n i t g e h l i f r e t e r u g a l . y l r n I r t s c u
can be found on page 6.
Provide good air flow
Make sure the airflow path to and from the unit is clear. Your air conditioner
puts the conditioned air out at the top of the unit, and takes in unconditioned air
at the bottom. Airflow is critical to good operation. It is just as important on the
u o i s t e d o t f e h u b d l i n i t g a h t t e h a l f r i

Unit placement

If your air conditioner can be placed in a window or wall that is shaded by a tree
o a r o n h t r e u b i d l i g n t , e h u t i n i w o l l e p
blinds on the sunny side of the dwelling will also add to your unit's efficiency.
o i t s n r o f e r m i v o g n a d n c e l n a n i t g
w o a o r n u t d e h u t i n x e e t o i r s i r o n b t
a r e t v e n e m o e r f e i c i f n e y l t U . i s g n r d
920-197-01
MODEL
XQ0
XQ0
XQ12 EQ08
YQ07
Figure 1
Electrical Shock Hazard
Make sure your electrical receptacle has the
same configuration as your air conditioner's
plug. If different, consult a Licensed Electrician.
Do not use plug adapters.
Do not use an extension cord.
Do not remove ground prong.
Always plug into a grounded 3 prong outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
NOTE: Your LCDI device will resemble one of these illustrations.
Figure 2
Insulation
Good insulation will be a big help in maintaining desirable comfort levels.
e h l i f r e t Doors should have weather stripping. Be sure to caulk around doors and
windows.
Proper installation of seal gasket
Make sure the seal gasket has been installed properly to minimize noise and
improve ef ciency. If the seal gasket has not been installed, please refer to
installation instructions on page 8.
c o l e k . d
p a s e r o
CIRCUIT RATING
OR TIME DELAY
FUSE
AMP VOLT
XQ06
XQ10
15 125
WARNING
RESET
TEST
WARNING
TEST BEFORE EACH USE
1. PRESS RESET BUTTON
2. PLUG LDCI INTO POWER
RECEPTACLE
3. PRESS TEST BUTTON,
RESET BUTTON SHOULD
POP UP
4. PRESS TEST BUTTON,
FOR USE
DO NOT USE IF ABOVE TEST
FAILS
WHEN GREEN LIGHT IS ON
IT IS WORKING PROPERLY
REQUIRED WALL
RECEPTACLE
NEMA NO.
5-15R
RESET
TEST
3