Festo CMMP-AS-MO Serie Manual Del Usuario página 8

Operating and environmental conditions CMMP-AS-...-M0
Permissible setup altitude above sea level
with rated output [m]
with power reduction [m]
Air humidity [%]
Protection class
Degree of contamination in accordance
with EN 61800-5-1
Operating temperature [°C]
Operating temperature with [°C]
power reduction of 2.5 % per
Kelvin
Storage temperature [°C]
Vibration and resistance to shocks
Operation
Transport
Electrical data [X40]
Control ports STO-A, 0V-A / STO-B, 0V-B
Nominal voltage [V]
Voltage range [V]
Permissible residual ripple [%]
Overvoltage discharge [V]
Nominal current [mA]
Starting current [mA]
Input voltage threshold
Switching on [V]
Switching off [V]
Switching time from High to [ms]
Low (STO-A/B_OFF)
Switching time from High to [ms]
Low (STO-A/B_ON)
Maximum positive test im- [µs]
pulse length at logic 0
Switch-off time to power output stage inactive and maximum tolerance time for test impulse
Input voltage (STO-A/B) [V]
Typical switch-off time [ms]
(STO-A/B_OFF)
Maximum tolerance time [ms]
for test impulse at 24 V
signal
Feedback contact C1, C2
Design
Max. voltage [V DC]
Nominal current [mA]
Voltage drop [V]
Residual current (contact open) [µA]
Switching time closing [ms]
(T_C1/C2_ON)
Switching time opening [ms]
(T_C1/C2_OFF)
Auxiliary supply 24V, 0V – output
Design
Nominal voltage [V]
Nominal current [mA]
Voltage drop [V]
Galvanic isolation
Galvanically isolated potential areas
Cabling
Max. cable length [m]
Screening
Cable cross section (flexible conductors, wire end sleeve with insulating collar)
One conductor mm²
Two conductors mm²
Tightening torque M2 [Nm]
1000
1000 ... 2000
0 ... 90 (non-condensing)
IP20
2
The integrated safety equipment requires compliance
with degree of contamination 2 and thus a protected
installation space (IP54). This must always be ensured
through appropriate measures, e.g. through installa-
tion in a control cabinet.
0 ... +40
+40 ... +50
-25 ... +70
in accordance with EN 61800-5-1, section 5.2.6.4
in accordance with EN 61800-2, section 4.3.3
24 (related to 0V-A/B)
19.2 ... 28.8
2 (related to nominal voltage 24 V)
31 (disconnect in case of error)
20 (typical; maximum 30)
450 (typical, duration approx. 2 ms; max. 600 at 28.8 V)
Approx. 18
Approx. 12.5
10 (typical; maximal 20 at 28.8 V)
1 (typical; maximum 5)
300 (related to nominal voltage 24 V and intervals
2 s between impulses)
19 20 21 22 23 24 25 26
4.0 4.5 5.0 6.0 6.5 7.0 7.5 8.0
2.0 2.0 2.0 2.5 3.0 3.5 4.5 5.0
Relay contact, normally open
30 (overvoltage-proof up to DC 60 V)
200 (not short-circuit proof )
1
10
(STO-A/B_OFF + 5 ms)
(STO-A/B_ON + 5 ms)
Logic power supply of the motor controller. Protected
against reverse polarity, overvoltage-proof up
to DC 60 V
24
100 (short-circuit proof, max 300 mA)
1 (for nominal current)
STO-A / 0V-A; STO-B / 0V-B; C1 / C2; 24V / 0V
30
When wiring outside the control cabinet, use screened
cable. Guide screening into the control cabinet /
attach to the side of the control cabinet.
0.25 ... 0.5
2 x 0.25 (with twin wire end sleeves)
0.22 ... 0.25
27 28
8.5 9.5
5.5 6.0