Select The Save Mode You Want To Use; 16- And 24-Zone Grx Control Units - Lutron GRAFIK Eye 4000 Serie Manual De Instalación

Select the Save Mode You Want to Use

Save modes enable you to specify how buttons on the control unit work. For example, adjustments to a zone's
settings can be temporary or saved for the current scene. Buttons can also be disabled to prevent accidental
changes.
Select Sd
2
ZONE 5 ZONE 6
Code Stands for
Sd
Save by Default
Sb
Save by Button
Sn
Save Never
4S
Four Scenes
bd
Button Disable

16- and 24-Zone GRX Control Units

The 16 and 24 zone GRAFIK Eye control units offer an expanded number of zones that can be controlled from a
single wall station. The zone intensity LEDs on the GRX-4x16 or GRX-4x24 will display the light level of a set of
eight zones at a time. Other sets of zones may be displayed and controlled by pressing the Zone Select Button.
Addressing
The GRX-4x16 and the GRX-4x24 control units take multiple, consecutive addresses. The GRX-4x16 control unit
takes up two consecutive addresses, and the GRX-4x24 control unit requires three. To ensure there are sufficient
addresses available, any GRX-4x16 and/or GRX-4x24 control units in the system should be addressed first.
Assigning Zones
When assigning zones use the chart below as a guide to see how zones are displayed on the Circuit Selector. The
chart is for a 24-zone control unit, which uses three addresses. A 16-zone control unit uses only two addresses.
Control Unit Addresses
A1, A2, A3
A2, A3, A4
.
.
.
.
.
.
A6, A7, A8
R
3
Select
save mode
FADE TEMPORARY
ZONES
M S
MASTER
Enter
(exit)
setup
mode
Description
C hanges to a zone's intensity/shade position or fade time are saved for the current scene.
To make temporary adjustments in Sd mode, refer to page 19. Typical user: Home theater
owner.
T EMPORARY ZONES LED is normally ON and all intensity/shade position and fade changes
are temporary unless the TEMPORARY ZONES LED is turned OFF with the TEMPORARY
ZONES button. Typical user: Restaurant manager.
T EMPORARY ZONES LED is permanently ON and cannot be turned OFF. In this mode, all
intensity changes are temporary. Typical user: Lighting designer.
A llows only the four SCENE buttons, OFF button, IR receiver, and MASTER 5 or 6 buttons
to operate. All other buttons on the control unit are disabled. Typical use: Rented meeting
space.
A ll buttons on the control unit are disabled. IR receiver and wallstations are still functional.
(Setup mode is still accessible by repeating Step 1.) Typical use: Public space.
Zones on Control Unit
1-8
9-16
17-24
1-8
9-16
17-24
.
.
.
.
1-8
9-16
17-24
To select the save mode you want to use:
1. Enter setup mode. Press and hold the SCENE 1 and
OFF buttons for about three seconds until scene LEDs
start cycling.
2. Select Sd. Press the FADE 5 button until Sd is dis-
played in the FADE window.
3. Select save mode. Press the MASTER 5 or 6
button to scroll through the save modes and select
one. Refer to the save mode descriptions in the table
1 4
below.
,
4. Exit setup mode. Press and hold the SCENE 1 and
OFF buttons until scene LEDs stop cycling.
Circuit Selector Display
A11-A18
A21-A28
A31-A38
A21-A28
A31-A38
A41-A48
.
.
.
.
A61-A68
A71-A78
A81-A88
GRAFIK Eye 4000 Series Control Unit Installer's Guide 21
®