Safety Notes; Important Notes; Functions; Information About Operation - LGB 24267 Manual Del Usuario

Safety Notes

• This model may only be used with the operating system designed for it.
• Use only switched mode power supply units and transformers that are designed
for your local power system.
• This locomotive must never be supplied with power from more than one power pack.
• Pay close attention to the safety notes in the instructions for your operating system.
• Not for children under the age of 15.
• WARNING! Sharp edges and points required for operation.

Important Notes

• The operating instructions are a component part of the product and must therefore
be kept in a safe place as well as included with the product, if the latter is given to
someone else.
• Please see your authorized LGB dealer for repairs or spare parts.
• Disposing: www.maerklin.com/en/imprint.html

Functions

• This model is designed for operation on LGB two-rail DC systems with conventio-
nal LGB DC train controllers or power packs (DC, 0 - 24 volts).
• Factory-installed multiple protocol decoder (DC, DCC, mfx).
• The model is programmed with locomotive address 03 for use with the LGB Multi
Train System (DCC). The locomotive is automatically recognized in operation with mfx.
• Mfx technology for the Mobile Station / Central Station.
Name set at the factory: 99 4652
• Volume can be changed for the sound effects
Preparation
Couple the locomotive to the tender:
• Plug the connecting wire for the locomotive into the socket on the tender and plug
the wire from the tender into the locomotive. Do not get the wires mixed up!
• Hang the coupler hook on the locomotive in the loop on the tender.
Mode of Operation Switch
This model has a four-position mode of operation switch in the tender under the right
water hatch (Figure 1).
Pos. 0 Locomotive stopped without current
Pos. 1 Locomotive motors, sound, and lighting are turned on
Pos. 2 & 3 Same as Pos. 1
Sound
This model has a volume controller in the tender under the left water hatch (Figure 2).
The whistle and the bell also can be triggered by the LGB Sound Magnet (17050) in-
cluded with this model. The 17050 snaps between the ties of most LGB track sections.
The magnet in the 17050 is under the LGB logo. If the contact is installed with the logo
on the right side of the track (in the direction of travel), it will trigger the whistle as the
model passes. When it is set to the other side, the bell will sound.

Multi-Protocol Operation

Analog Operation
This decoder can also be operated on analog layouts or areas of track that are
analog. The decoder recognizes alternating current (DC) and automatically adapts
to the analog track voltage. All functions that were set under mfx or DCC for analog
operation are active (see Digital Operation).
Digital Operation
The decoders are multi-protocol decoders. These decoders can be used under the
following digital protocols: mfx or DCC.
The digital protocol with the most possibilities is the highest order digital protocol.
The sequence of digital protocols in descending order is:
Priority 1: mfx; Priority 2: DCC; Priority 3: DC
Note: Digital protocols can influence each other. For trouble-free operation, we re-
commend deactivating those digital protocols not needed by using CV 50. Deactivate
unneeded digital protocols at this CV if your controller supports this function.
If two or more digital protocols are recognized in the track, the decoder automatically
takes on the highest order digital protocol, example: mfx/DCC; the decoder takes on
the mfx digital protocol (see previous table).
Note: Please note that not all functions are possible in all digital protocols. Several
settings for functions, which are supposed to be active in analog operation, can be
done under mfx and DCC.
Notes on digital operation
• The operating instructions for your central unit will give you exact procedures for
setting the different parameters.
• The values set at the factory have been selected for mfx/DCC in order to guarantee
the best possible running characteristics. Adjustments may have to be made for
other operating systems.
• The setting done at the factory does not permit operation with opposite polarity
DC power in the braking block. If you want this characteristic, you must do without
conventional DC power operation (CV 29/Bit 2 = 0).
mfx Protocol
10