Tabla de contenido
Idiomas disponibles
Idiomas disponibles
7200
PROGRAMMING
There are three monitor programming modes: assignment of an identifica-
tion code or call code (indispensable), assignment of a secondary identifica-
tion code (for video interphones associated with a master video interphone),
programming of push-buttons for auxiliary services and intercommunicating
calls (when necessary).
Programming must be performed with the system switched on, without
active communication and only after connecting the interphones/video in-
terphones to the system and programming the panels.
Programming the identification code
The identification code is to be programmed by means of an entrance panel
(main- "Master"), present on the installation and already configurated. The
video-interphone is supplied without associated identification code. To
check this, press the
push-button and the video-interphone will emit
a triple "Beep".
Attention: during the interphone/video interphone identification code
programming you have 30 seconds from the moment you enter the
programming in the interphone/video interphone and the moment you
press the call push-button on the panel or you send the code.
Programming phase:
1)
Press and hold down
2)
Press and hold down also
3)
Wait for nearly 3 seconds until the red led
4)
Release both push-buttons
conds to carry out any of the described programmings.
5)
Press and hold down the
6)
After approximately 2 seconds the video door entry unit emits a high tone,
it self-starts and communication is enabled with the main entrance panel.
7)
On the entrance panels with push-buttons press the call push-button
corresponding to the video-interphone, on the alphanumeric entrance
panel, on the contrary, enter the call code and press "
8)
If the system already contains an audio/video door entry unit that has the
same associated identification code, the panel emits a low sound signal
and the operation needs to be repeated from the start in order to assign a
different code.
9)
If not, the code is associated to the video-interphone and the commu-
nication is terminated.
Programming the secondary identification code
The programming of the secondary identification code is required only
when you want more than a video- interphone to ring at the same time
with the same push-button or call code. The video-interphones which must
ring simultaneously are associated with the same push-button to the same
group. The "master" interphone / video-interphone is programmed in first
place by means of the previous procedure: "programming the identification
code". The additional interphones / video-interphones are programmed with
the secondary identification code (see table shown in the wiring diagram
section enclosed with the electronic TWO WIRE ELVOX entrance panels).
A maximum of three audio door entry units plus one group master can be
associated with the same group, without the need for programmer Type
950C or SaveProg.
Programming phase:
1) Press and hold down
2) Press and hold down also
3) Wait for nearly 3 seconds until the red led
4) Release both push-buttons
5) Press both push-buttons
6) After 2 seconds the video-interphone emits a high-pitched tone and
gets in communication with the entrance panel.
7) Release the door lock
EN
.
together with
.
flashes.
and
. You have now 5 se-
lock push-button.
".
.
together with
.
flashes.
and
.
and
.
and the self-start
push-buttons.
8) On the push-buttons entrance panels press the call push-button corre-
sponding to the main (already programmed) interphone / video-inter-
phone, on the alphanumeric entrance panel, on the contrary, enter the
same call code of the "Master" interphone / video-interphone and press
"
".
9) If on the installation there is already an interphone / video-interphone with
the same associated identification code, the panel emits a low-pitched tone
and you must repeat the operation from the beginning.
10) Once the secondary identification code is associated to the video-inter-
phone, the communication is terminated.
To find out the assigned number, refer to the table given in the wiring dia-
grams section of the Two-Wire manual entrance panel or electronic unit.
Programming the push-buttons
The video-interphone is supplied with 3 push-buttons for the following
functions: lock release, self-start and "stair light" auxiliary service, which
activates the 1st relay of the 1st actuator (type 69HR), if connected to the
installation and with other 6 push-buttons for intercommunicating calls or
auxiliary services.
To change the operation type of push-buttons it is necessary to use pro-
grammer type 950C or SaveProg, with the exception of the assignation of
the functions for the intercommunicating calls and self-start to a specific
entrance panel.
Programming the push-buttons for the intercommunicating calls
(In the audio/video door entry unit where the intercom call is to be sent
it is necessary to pick up the handset (8870, Petrarca and Giotto se-
ries) or hold down push-button
Programming phase:
1) Press and hold down
2) Press and hold down also
3) Wait for nearly 3 seconds until the red led
4) Release both push-buttons
5) Press and hold down the
one of push-button:
,
6) After 2 seconds the video-interphone emits a high-pitched tone, while
the other interphone / video-interphone emits a three-tone ascending
scale.
7) Release the
push-button related to the intercommunicating call
(or one of push-button:
8) On the interphone/monitor called (with the 3-tone ring), press the lock
release push-button.
9) A high-pitched tone confirms the end of the procedure.
Repeat the procedure also for the other interphones / video-interphones
ad possible intercommunicating call push-buttons.
Programming the self-start push-button to a specific entrance panel.
Programming phase:
1)
Press and hold down
2)
Press and hold down also "
3)
Wait for nearly 3 seconds until the red led "
4)
Release both push-buttons
5)
Press and hold down the "
one of push-button:
,
6)
After nearly 2 seconds the video-interphone emits a high-pitched tone.
7)
Release the push-button "
push-button:
,
8)
On the entrance panels with push-buttons press the call push-button
corresponding to the video -interphone; on the alphanumeric entrance
panel, on the contrary, enter the call code and press "
9)
A high-pitched tone will confirm the end of the procedure.
(for the 6600 and 7200 series).
.
together with
.
flashes.
and
.
push-button to be programmed (or
,
,
).
,
,
,
).
.
" together with "
".
" flashes.
and
.
" push-button to be programmed (or
,
,
).
" related to the self-start (or one of
,
,
).
".
9
Tabla de contenido
