BFT MICHELANGELO Serie Instrucciones De Uso página 24

WARNING! Important safety instructions. Carefully read and comply with
the Warnings booklet and Instruction booklet that come with the product as
incorrect installation can cause injury to people and animals and damage to
property. They contain important information regarding safety, installation,
use and maintenance. Keep hold of instructions so that you can attach them
to the technical le and keep them handy for future reference.
1) GENERAL SAFETY
WARNING! An incorrect installation or improper use of the product can
cause damage to persons, animals or things.
Warnings" lea et and "Instruction booklet" supplied with this
product should be read carefully as they provide important information
about safety, installation, use and maintenance.
to the provisions set out by current standards. Keep nylon or polystyrene
bags out of children's reach.
reference.
speci ed in the present documentation. Any other use not speci ed in
this documentation could damage the product and be dangerous.
improper use of the product, or use which is di erent from that expected
and speci ed in the present documentation.
ments of the following European Directives: 2004/108/EEC, 2006/95/EEC,
98/37/EEC, 99/05/EEC (and later amendments). For all countries outside
the EEC, it is advisable to comply with the above-mentioned standards,
in addition to any national standards in force, to achieve a good level of
safety.
ing structures (door, gates etc.), as well as from any deformation which
might occur during use.
European Directives: 2004/108/EEC, 2006/95/EEC, 98/37/EEC, 99/05/EEC
and subsequent amendments.
the installation. Also disconnect any bu er batteries, if tted.
having a contact opening distance equal to or greater than 3,5 mm.
the power supply mains.
closure (doors, gates etc.) and all system components provided with an
earth terminal.
to protect the area from any danger caused by squashing, conveying and
shearing, according to and in compliance with the applicable directives
and technical standards.
can be easily seen, and x a Warning sign to the structure.
and correct operation when other manufacturer's components are used.
by the Company.
manual opening operation in case of emergency.
area.
order to avoid unintentional automation activation.
tion system, and always request the assistance of quali ed personnel.
is not allowed.
prescribed by the EN 12978 Standard.
WARNINGS
Correct controller operation is only ensured when the data contained in the
present manual are observed. The Company is not to be held responsible
for any damage resulting from failure to observe the installation standards
and the instructions contained in the present manual.
The descriptions and illustrations contained in the present manual are not
binding. The Company reserves the right to make any alterations deemed
appropriate for the technical, manufacturing and commercial improvement
of the product, while leaving the essential product features unchanged, at
any time and without undertaking to update the present publication.
24
- MICHELANGELO
INSTALLATION MANUAL
USE OF AUTOMATION
As automation can be remotely controlled and therefore not within sight, it is
WARNING! In case of any malfunction in the safety devices, take imme-diate
action and require the assistance of a specialised technician.
It is recommended to keep children at a safe distance from the automation
eld of action.
CONTROL
The automation system is used to obtain motorised access control. There are
di erent types of control (manual, remote, magnetic badge, mass detector
-Fig. AH- etc.) depending on the installation requirements and characteristics.
For the various control systems, see the relevant instructions.
MAINTENANCE
WARNING: before opening the door, the spring must be unloaded
(vertical boom). WARNING: Before carrying out any maintenance to the
installation, disconnect the mains power supply. The following points need
checking and maintenance:
- Photocell optics. Clean occasionally.
- Electric edge. Carry out a periodical manual check to ensure that the edge
stops the bar in case of obstacles.
- Dismantle the gearmotor and replace the lubricating grease every two
years.
- When any operational malfunction is found, and not resolved, discon-
-
nect the mains power supply and request the assistance of a specialised
technician (installer). When the operator is out of order, activate the
emergency release (see Fig. Y), if necessary, so as to release the manual
boom opening and closing operations.
SCRAPPING
Materials must be disposed of in conformity with the current regulations.
-
In case of scrapping, the automation devices do not entail any particular
risks or danger. In case of recovered materials, these should be sorted out
by type (electrical components, copper, aluminium, plastic etc.).
DISMANTLING
WARNING: before opening the door, the spring must be unloaded (verti-
cal boom). When the automation system is disassembled to be reassembled
on another site, proceed as follows:
- Disconnect the power supply and the entire electrical installation.
- Remove the actuator from its xing base.
- Disassemble all the installation components.
- In the case where some of the components cannot be removed or are
damaged, they must be replaced.
-