Nice E MAT ST 324 Instrucciones Y Advertencias Para La Instalación Y El Uso página 8

5.8 - Automatic programming of both limit switches
WARNING! – This programming is intended for awnings with retainer lock on both the limit switches ("0" and "1").
Warnings • This procedure overwrites previously adjusted heights with the new heights using this same procedure. • Memorising the limit switches with this pro-
cedure, the two heights are controlled and updated constantly by the "limit switch self-update" function (see paragraph 7.2). • Every time the motor is powered, 2
movements are performed if at least one transmitter and the limit switch heights are not in the memory.
Before starting the procedure, bring the awning to the midpoint of its stroke.
01. Run the UP command by keeping the s (or t) key pressed and wait for the awning to stop automatically as result of the impact against the structure (= upper
limit switch "0"). Upon completion, release the key.
02. Run the Down command by keeping the t (or s) key pressed and wait for the awning to stop automatically as result of the impact against the structure (= lower
limit switch "1"). Upon completion, release the key.
01
Notes • When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements. • After this programming, the s key will command the Raise manoeuvre and the t key will com-
mand the Lower manoeuvre. During the Raising manoeuvre, the awning will be stopped by the impact against the mechanical blocks of the structure (= upper limit
switch "0"), while during the Lowering manoeuvre the awning will stop at the lower limit switch ("1") established by the installer.
5.9 - Adjusting height ("H") for partial opening/closing
The motor can manage up to 30 partial openings/closings, each called "H height". These heights can only be adjusted after adjusting limit switches "0" and "1". The
following procedure makes it possible to adjust one "H" height at a time.
Warning – If you want to change the position a given "H" height that is already memorized, repeat the present procedure by pressing at point 06 the key associated
with that height.
Before beginning the procedure, bring the awning to the "H" height you want to memorize.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the n key pressed again and wait for the motor to perform 4 movements. Upon completion, release the key.
03. Keep pressed the s and t keys simultaneously and wait for the motor to perform two movements. Upon completion, release the keys.
04. Fine adjustment of position: Perform key pulsing on the s key and t key until the awning is brought to the partial height you want (at each pulse the awning
moves a few millimetres).
05. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
06. • To memorize the FIRST "H" height: on the transmitter you are using for this procedure, keep the s and t keys pressed simultaneously and wait for the
motor to perform 4 movements. Upon completion, release the keys.
• To memorize the NEXT "H" height: on the new unmemorized transmitter keep the desired key pressed and wait for the motor to perform 4 movements. Upon
completion, release the key.
01
"H"
5
sec.
04
fine adjustment
Note – When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5.10 - Memorising a SECOND (third, fourth, etc.) transmitter
To perform these procedures you must have a transmitter ("old") already memorised.
5.10.1 - Memorising a second transmitter "Mode I"
Warning! – This procedure memorises the new transmitter in "Mode I", regardless of the Mode in which the old to transmitter was memorised.
Before starting the procedure, bring the awning to the midpoint of its stroke.
01. (on the new transmitter) keep the n key pressed for 8 seconds and then release it (in this case the motor does not perform any movement).
02. (on the old transmitter) Give for 3 pulse to the n key, provided it has already been memorized.
03. (on the new transmitter) Give 1 pulse to the n key. After a while the motor performs 3 movements to confirm the memorisation. Warning! If the motor performs 6
movements, it means that its memory is full.
7 – English
limit switch "0" (against the box)
02
2
05
"H"
5
sec.
02
"0"
4
5
sec.
06
3
"1"
limit switch "1" (against the box)
03
2
5
sec.
8
sec.