Accessories; Installation - Thermador Masterpiece Serie Manual De Instalación

A C C E S S O R I E S
Flexible Blower
Thermador Model VTD600P
MODEL DESCRIPTION
Non-Duct Recirculating Kit
Used in applications where ducting is not
feasible or available. Mount to toe kick
or base of a cabinet and attach directly
to VTD600P Flexible Blower using 8"
(203 mm) round duct. Kit can be rotated
so that the exhaust is not directly at your
feet. Includes decorative cover plate.
UCVRECIRC
UCVFILTER
(replacement i lter)
Rough-in Plate - 8" (203 mm) Round
Use for applications where 8" (203 mm)
round duct or elbow attaches to front
of airbox (VTD600P inline blower

installation).

CVTFRONT8
Rough-in Plate - 6" or 10" (152 mm or
254 mm) Round
Use for applications where 6" or 10"
(152 mm or 254 mm) round duct or
elbow attaches to front of airbox (inline
or remote blower installation).
CVTFRONT6
CVTFRONT10
Extension Cable - 5-ft. (1.5 m)
Used in applications where the electrical
panel is remotely mounted. If blower
discharge is down, electrical panel
must be relocated. Extends electrical
panel cable an additional 5-feet (1.5 m)-
with the ability to connect up to two
EXTNCE5
extension cables.
Gas Cooktop Seal Kit - 30-in. (762 mm),
36-in. (914 mm)
Used to provide seal between gas
cooktop and downdraft. Also includes
cabinet hole cover plates. Two grilles are
provided in the kit, you may only need
one for your specii c installation.
UCV30ST
UCV36ST
Rectangular Duct - 2-ft. (0.6 m) sections
(1-7/8" x 19" /48 mm x 483 mm)
Galvanized steel construction.
2-ft. (0.6 m) sections can be connected
together.
CVDUCT2
Rectangular Adapter for 1-7/8" x 19"
(48 mm x 483 mm)
Use to connect 1-7/8" x 19" (48 mm x
483 mm) rectangular duct directly to
downdraft when using side, below or
rear exhaust.
CVTRECT2
Page 12
(purchase separately)
Inline and Remote Blowers
Thermador Models VTI610, VTR630, VTI1010, VTR1030, VTR1330
MODEL DESCRIPTION
1-7/8" X 19" (48 mm x 483 mm)
to 8" (203 mm) Round
Transition
Rectangular to 8" (203 mm) round
transition for left, right, below, or rear
exhaust - using Model VTD600P Flex
Blower. Can be attached to downdraft
unit or rectangular duct (CVDUCT2).
CVTSIDE8
1-7/8" X 19" (48 mm x 483 mm) to 6" or
10" (152 mm or 254 mm) Round
Transition
Rectangular to 6" or 10" (152 mm or
254 mm) round transition for left, right,
below, or rear exhaust using inline or
remote blower. Can be attached to
downdraft unit or rectangular duct
(CVDUCT2).
CVTSIDE6
CVTSID10
Extension Cable - 25-ft. (7.62 m)
The remote or inline blower harness
should be routed through the knockout
and secured with a 3/4" (19 mm) strain
relief. The 25 ft. Extension Cable can
then be connected to the Adapter Cable
included in EXTNSET4 Accessory Kit and
Connects to Hood
B
then to the hood electrical panel.
Connects to Remote
C
or In-line Blower
EXTNCB25W
Extension Cable Connection Kit
Cable connection kit containing
EXTNSET4
(4) accessory cable adapters to
connect a variety of blower and hood
combinations.