Emptying The Recovery Tank; After Use; Shutting Down The Propane Engine; Important - Nilfisk-Advance Captor 4300 Instrucciones De Uso

EMPTYING THE RECOVERY TANK

1 Drive the machine to a designated waste water "DISPOSAL SITE".
2 To empty, pull the Drain Hose (7) from its storage area, then remove the plug (hold the end of the hose above the water level in the tank
to avoid sudden, uncontrolled fl ow of waste water).
3 Flush the tank and drain hose with clean water.
4 Put the plug back into the hose and return the hose to its storage area.
SERVICE NOTE: The recovery tank can be tipped out to the side for cleaning after emptying. Release the Latch (48) at the front of the tank
next to the engine air fi lter (8) and then pull out on the tank with grip (31) until the tank reaches the end of its tether. Remove the recovery
tank lid for easier cleaning.

AFTER USE

1 Raise the squeegee, the scrub brushes, and the brooms.
2 Shake the dust control fi lter and empty the hopper.
3 Drain and fl ush the recovery tank.
4 Flush the vacuum hose and squeegee by opening the recovery tank lid and running water down the pickup tube on the right side of the
tank. SERVICE NOTE: Tip the recovery tank out and check the squeegee hose elbow below the tank to make sure it has fl ushed out
completely.
5 Remove and clean the squeegee tool.
6 Remove and clean the scrub brushes. Rotate the scrub brushes.
7 Wipe the machine with a damp cloth.
8 Perform all required maintenance before storage.
9 Move the machine to a clean, dry storage area.
10 Store the machine with the brooms, the squeegee and the scrub brushes in the UP position, and the tank covers open so that the tanks
can air out.
REPORT ANY DEFECT OR MALFUNCTION NOTED DURING OPERATION TO AUTHORIZED SERVICE OR MAINTENANCE
PERSONNEL.
SHUTTING DOWN THE DIESEL / GASOLINE ENGINE
1 Put all controls to the OFF position.
2 Raise the squeegee, the scrub brushes, and the brooms.
3 Push the Engine Speed Switch (G) to change to "Idle" speed and let the engine idle for 30 seconds.
4 Apply the Parking Brake (GG).
5 Turn the Key Ignition Switch (MM) OFF and remove the key.

SHUTTING DOWN THE PROPANE ENGINE

1 Put all controls to the OFF position.
2 Raise the squeegee, the scrub brushes, and the brooms.
3 Turn the service valve on LP gas tank OFF.
4 Push the Engine Speed Switch (G) to change to "Idle" speed and let the engine idle until all the LP gas is dispelled from the line.
5 Apply the Parking Brake (GG).
6 Turn the Key Ignition Switch (MM) OFF and remove the key.
CHECK THE HYDRAULIC OIL LEVEL
WARNING!
To avoid hydraulic oil injection or injury, always wear appropriate clothing and eye protection when working with or near hydraulic
system.
See Figure 3. Remove the Right Engine Access Panel (37) and look at the Gauge (A) on the side of the reservoir. If the oil level is
below the minimum level, add 10W30 motor oil until the gauge reads between the minimum and maximum levels. Change the oil if
major contamination from a mechanical failure occurs. SERVICE NOTE: Remove the small access panel (49) directly above the
reservoir to add oil. This panel is held on by (2) wing nuts on the underside of the panel. The large Allan Head Plug (B) on the top of
the reservoir is for adding oil.

IMPORTANT!

This machine is equipped with an Indicator Light (F) which lights if the "In Tank" oil fi lter requires changing. Remove fi lter
element from the fi lter cup (C) and replace with new fi lter. Hydraulic fi lter is found on top of the Hydraulic Reservoir (36) as
shown.
revised 11/06
FORM NO. 56041580 - Captor
ENGLISH / A-21
4300, 4800, 5400 / CR 1100, 1200, 1400 - A-21
™