Electrical Safety - Jacuzzi flexa tower ELT4 Manual De Instalación

Ocultar thumbs Ver también para flexa tower ELT4:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

• After using the electrical functions of the shower enclosure, it is ad-
visable to switch off the master switch (§ "Electrical safety" chap-
ter).
For all maintenance and/or repair operations that require
the replacement of components, original Jacuzzi
parts must be used. Failure to comply with this regulation
while carrying out this operation will mean that the Man-
ufacturer is not liable for any damage.
Models with thermostatic mixer
Dismantling and cleaning the thermostatic valve
The thermostatic valve is provided with mesh filters, to trap any im-
purities in the water.
Over time, these filters could become clogged and, therefore, inhibit
the functions of the mixer tap; to clean the valve, remove it in this way:
I
Turn off the water supply (hot and cold) to the shower enclosure.
i
I
(
)
19
Drain the water present in the mixer unit by turning the
diverter ring (5) to the symbol "under seat outlet" and open the stop
cock completely (3) ; however, a little water will remain inside the
brass part). After emptying the mixer unit, close the stop tap by turn-
ing the dial to the previous position.
i
I
(
)
19
Remove the two dial caps (1), by using the tip of a screw-
driver if necessary; be careful not to scratch the dial.
i
I
(
)
20
Remove the screws (2) and loosen the knobs (3) and (3a).
i
I
(
)
20
Unscrew the cover (4) and then remove the diverter ring (5).
i
I
(
21
)
Remove the plate (6) using the slit as a lever, be care-
ful not to scratch the plate and the methacrylate panel.
i
I
(
)
21
Unscrew the centering collar (7) and the cover (7a).
i
I
(
22
)
Ease out the thermostatic valve (8).
Clean the mesh filters with a little brush and rinse; if scale is pre-
sent, wash with specific products.
Reassemble the various components, following the same procedure
backwards; also follow these instructions:
- the stopcock knob (3) must be in a vertical position (turned off).
i
I
(
)
22
Attach the thermostatic valve so that the sprig (9) (screw
peg) is facing downwards, and it can enter the cut in the brass casing.

Electrical Safety

Jacuzzi
®
hydromassage products are safe appliances, manufactured
according to EN 60335-1, EN 60335-2-105, EN 55014-1, EN
55014-2 norms. They are tested during production to guarantee user
®
spare
safety. The installation must be carried out by qualified persons who
must be able to guarantee compliance with the current national reg-
ulations and who must also be certified to carry out the installation.
It is the responsibility of the installer to choose the
materials according to their use, to carry out the
work correctly, to check the condition of the system
to which the appliance is to be connected and its
suitability in order to guarantee user safety.
FLEXA shower enclosures are class "1" appliances and must be an-
chored securely and connected permanently to the electric network
and earth system without any intermediate junctions.
The electric network and earth system of the build-
ing must be in working order and must comply with
the provisions of the law and specific regulations in
force in that country.
An appropriate device must be provided, as part of
the fixture and installed in compliance with cur-
rent regulations, which disconnects the equipment
from the mains.
A multiple-pole disconnect switch must be installed for connection
to the mains. This device must ensure complete disconnection un-
der class III overcurrent conditions. The breaker must be located in
a position that respects bathroom safety regulations.
In accordance with regulations, the switch and other
electrical devices must be located in an area that can-
not be reached by the person using the appliance.
The installation of electrical devices and appliances (sockets, switches,
etc.) in bathrooms must comply with the legal requirements and standards
of each country. In particular, no electrical installation is permitted with-
in 60 cm of the shower enclosure or at a height of less than 225 cm.
If the building's electrical system is not able to gua-
rantee a stabile power supply, it is recommended
to install a voltage stabiliser that suitably dimen-
sioned for the required power upstream of the e-
quipment.
14
0,6 m
0,6 m

Hide quick links:

Tabla de contenido
loading

Tabla de contenido