EGO POWER+ HTA2000 Manual De Instrucciones página 365

CONNECTING THE EXTENSION POLE BETWEEN THE
POWER HEAD AND THE POLE SAW ATTACHMENT
(Optional)
The extension pole extends the cutting range. It should to
be connected between the power head and the pole saw
attachment.
Follow the process in the section "CONNECTING THE POLE
SAW ATTACHMENT TO THE POWER HEAD "to install and
secure the extension pole between the pole saw attachment
and power head (Fig. C).
WARNING:
Failure to secure the attachment and
power head/extension pole as instructed above could
result in serious injury or death.
WARNING:
Never attach or adjust any attachment
while the power head is running or with the battery
installed. Failure to stop the motor and remove the battery
may cause serious personal injury.
OPERATION
DANGER:
Never cut near power lines, electric cords,
or other electric sources. If the bar and chain jams on
any electrical cord or line, DO NOT TOUCH THE BAR,
CHAIN OR THE ALUMINUM POLE! THEY CAN BECOME
ELECTRICALLY LIVE AND MAY BE VERY DANGEROUS.
Continue to hold the pole saw by the insulated rear handle
or lay it down and away from you in a safe manner.
Disconnect the electrical service to the damaged line or
cord before attempting to free the bar and chain from the
line or cord. Contact with the bar, chain, other conductive
parts of the pole saw, or live electric cords or lines could
result in death by electrocution or seri ous injury.
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING: Always wear eye protection, along with
hearing protection. Failure to do so could result in objects
being thrown into your eyes and other possible serious
injuries.
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced.
WARNING:
To prevent serious personal injury,
remove the battery pack from the tool before servicing,
cleaning, changing attachments or removing material
from the unit.
APPLICATIONS
You may use this product for the purpose listed below:
◾
Limbing
◾
Pruning
NOTICE:
The tool is to be used only for its prescribed
purpose. Any other use is deemed to be a case of misuse.
FILLING OILTANK WITH BAR AND CHAIN LUBRICANT
WARNING:
Do not smoke or bring any fire or flame
near the oil or the pole saw. Oil may spill and cause a fire.
NOTICE:
The pole saw is not filled with oil at the time of
purchase. It is essential to fill the tank with chain oil before
use. Chain life and cutting capacity depend on optimum
lubrication. The chain is automatically lubricated with chain
oil during operation. Oil level should also be checked after
every 20 minutes of use and refilled as needed.
1. Remove the battery pack from the power head.
2. Clean the oil tank cap and the area around it to ensure
that no dirt falls into the oil tank.
3. Place the pole saw attachment upright and rotate the oil
tank cap counterclockwise to remove it (Fig. D).
4. Carefully pour the bar and chain oil into the tank until it
fills to the tank neck. Be careful not to let the oil spill from
the opening. Wipe off any excess oil and close the oil
tank cap.
NOTICE:
◾
Use OREGON ® bar and chain oil for best results. It is
specially designed to provide low friction and faster cuts.
◾
Do not use dirty, used or other contaminated oils.
Damage may occur to the bar or chain.
PREPARATION FOR CUTTING (Fig. B)
Refer to "Important Safety Instructions" earlier in this
manual for appropriate safety equipment.
◾
Lift the tip of the guide bar to check for any sagging
in the chain. The chain is correctly tensioned when
there is no sag on the underside of the guide bar and
the chain is snug, but it can be turned by hand without
binding. If the tension requires adjustment, refer to the
"REPLACING THE BAR AND CHAIN" section in the
MAINTENANCE section of this manual for adjustment
instructions.
◾
Check the tension of the cover screw before use. If it
is loose, securely tighten the cover screw by turning it
clockwise.
◾
Check the sharpness of cutting teeth on the saw chain
and make sure the chain is well lubricated.
POLE SAW ATTACHMENT — PSA1000
EN
9