Roadstar TT-540 Manual De Instrucciones página 4

poly foam packaging), unwind the cord and insert the small plug into the DC JACK in the back of
the record player, then plug the 2-pin plug into a AC power.
Release the Tonearm Clamp, and remove the stylus protector.
1. Rotate the ON-OFF VOLUME SWITCH located on the front panel to switch the unit ON.
2. Place a record on the turntable, over the central spindle. Place the EP adapter over the
central spindle when playing 17cm EP records.
3. Set the Speed Selector to 33, 45 or 78 rpm according to the record.
4. Release the tonearm clamp, and remove the protective cap from the stylus.
5. Lift the Tonearm .
6. Move the tonearm to the beginning of the record, or to the start of a particular track.
7. Gently lower the tone arm onto the record to start playing.
8. When the record is finished, lift the tonearm from the record to the rest .
9. To stop manually, lift the tonearm from the record and return it to the rest.
10. Re-adjust the ON-OFF VOLUME SWITCH to the desired sound level and rotate the
TONE control switch as required.
Note: After use and removing the record, always push the ARM LOCK upwards again
before placing the TONE ARM back on it – then lock it and close the cover.
Notes: Do not stop or turn the platter manually.
Moving or jarring the turntable without securing the Tonearm clamp could result in damage to the
Tonearm.
Replace the protective cap on the stylus when not in use.
REMOVING THE NEEDLE HOLDER (OR STYLUS)
The record player is already fitted with a universal needle (or stylus) suitable for playing
1
33 / , 45 or 78rpm records. The procedure for removing and re-fitting the needle is as
3
follows:
Gently pull down the tip of the stylus holder (1).
Pull the cartridge forward (2). Pull it out and remove it from the tone arm head (3).
FITTING A STYLUS CARTRIDGE
After following the "Removing the Needle Holder" instructions on the previous page, follow
steps 1 to 4 below to refit it:
1. Position the red stylus holder with the Sapphire stylus facing down.
2. Line up the tab at the back of the stylus holder with the tone arm cartridge ( picture 1).
3. Insert the stylus holder with its front end at a downward angle (see picture 2 below).
if f f l l
English
il i i l
English
3 4
Additional Stylus Information
The red stylus holder has a very small Sapphire stylus tip that is barely visible. Make
•
sure the replacement needle you purchased is the same as the needle already on the tone
arm.
See the Specifications section for further details on how to purchase one*
• This universal needle is safe to use for all three (33
Note: We do recommend that a needle specifically for use with 78rpm records is used
if you are going to play a lot of 78rpm records.
• When to replace the needle depends on how often you use your turntable and the
condition of the records played.
• The Sapphire stylus will give an average of 1000 hours playing time.
LINE OUT CONNECTION
1. Connect the Auxiliary cable (not supplied) to the LINE OUT JACK on the rear of the
record player and the other end of the cable to the auxiliary inputs of the external
component, e.g. another Hi-Fi unit, Amplifier, PC, etc.
2. Check the volume level of your external component and adjust it if necessary.
3. Refer to the instruction manual of the external component for its correct operation.
SUBWOOFER OUTPUT JACK
The subwoofer output jack enables you to attach an active subwoofer (not supplied) which
will enhance bass response. Please contact your retailer for suitable subwoofer models.
LINE-IN CONNECTION & OPERATION
Any component with an audio output, such as for instance a DAB Radio Module, CD/Cassette
Player, MP3 Player, can be connected by using a cable with a 3.5mm dia. jack plug (a 3.5mm
to 3.5mm Line In cord is supplied).
1. Turn the unit on and adjust the volume.
2. Plug the supplied Line In cord into the LINE-IN JACK on the rear of the unit.
3. Insert the plug at the other end of the Auxiliary cable into the Output Jack or 3.5mm dia.
Headphone Jack of the external Audio Player.
4. Switch the other Audio Player on, play the music and adjust its volume if required.
SPECIFICATIONS
Power Supply
AC Adapter:
Output power
Design and specifications are subject to change without notice.
1
/ , 45 & 78rpm) speed records.
3
100-240 V ~ 50Hz out 12V
2 x 1.5 W RMS