Tabla de contenido
.
(4,
.
.
.
,
,
.
,
.
,
.
,
.
,
,
.
PARTS LIST FTZ-600
REF. NR.
DESCRIPTION
1
FIXED SHEET
2
GUIDE
3
KNOB
5 T/M 7
UPPER SAFEGUARD COMPLETE
10
RIVING KNIFE
13
FOOT
16
KNOB
24+25
LOWER SAFEGUARD WITH COVER
28
WATER TANK
29
INNER FLANGE
30
DIAMANT CUTTING DISC 180X22,2X2,2
31
OUTER FLANGE
32
NUT
33
ANGLE GUIDE
34
SWITCH
42
. 2)
ı
CE
.
EN61029-1, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
98/37/
73/23/
89/336/
01-01-2004
ZWOLLE NL
W. Kamphof
PC
407101
407102
407455
407103
407104
407105
407456
407106
407107
407108
TCA1004
407109
407110
407111
407112
( GR )
,
TILE CUTTER
TECHNICAL SPECIFICATIONS
Voltage
Frequency
.
Power consumption
No load speed
Max. depth of cut 90º
Cutting angle
Ø Cutting blade
Table dimensions
Lpa (sound pressure level) | 63.08 dB(A)
Lwa (sound power level) | 76.08 dB(A)
Vibration
CONTENT OF THE BOX
1 Tile cutter
1 Water tray
1 Full-length adjustable fence
1 Mitre guide
1 Set of instructions
1 Safety instructions
1 Guarantee card
USE
This tool is suitable for cutting various wall and floor tiles
with a maximum tile size of 500 x 500 x 35mm. The dia-
mond wheel can be replaced by the customer. It is not
permitted to use the tool for any other materials.
SAFETY INSTRUCTIONS
These instructions use the following images:
Means a risk of physical injury, danger of life or the
risk of damaging the machine if these instructions
are ignored.
Please read these instructions carefully before using this
tool. Ensure you are familiar with the tool and its opera-
tion. Maintain this tool in accordance with the instruc-
tions to ensure it functions properly. Please keep these
instructions for use and the safety instructions with the
tool.
SAFETY MEASURES
•
Check your powertool for damage before starting
your work, particularly the diamond blade. All parts
must be fitted properly and must meet all require-
ments in order to guarantee the tool's smooth ope-
ration. Any safety guards or any lightly damaged parts
must be checked to see if they still function properly
before continuing the use of the tool. Moving parts,
and the diamond-blade guard in particular, must be
fitted properly and must not jam. Do not use tools
that cannot be switched on or off with the switch.
•
The diamond-blade guard must not be jammed or
Ferm
Ferm
removed.
•
A jamming guard must be repaired immediately.
•
The riving knife must not be removed.
INSTALLING THE TILE CUTTER
•
The tile cutter may only be used as a fixed tool and
should be screwed down to a level and horizontal
surface. Please use the screw holes in the base of the
machine.
•
The electrical supply must be connected to a 230 V
| 230 V~
earthed wall socket. The mains voltage must comply
| 50 Hz
with the information on the type plate, and must be
| 600 W
protected by a circuit breaker.
| 2,800/min
•
Do not use the power cable to pull the plug from the
| 35mm
socket. Protect the cable against heat, oil and sharp
| 0 - 45°
objects.
| 180x22.2x2.2mm
| 360 x 330mm
Only use accessories and auxiliary equipment men-
tioned in the instructions for use or recommended
| 1.34 m/s2
or mentioned by the manufacturer. Using other accessories or
auxiliary equipment may carry a risk of injury for you and
others.
OPERATION
Fig.1
•
Before starting the job, please ensure there is suffi-
cient water in the water tray (4) i.e. the diamond
blade runs through the water. During the job, the
water tray must be topped up.
•
Do not start working before the maximum speed has
been reached.
•
The diamond blade must NEVER be exposed to side-
ways pressure; they can break and the flying pieces
become projectiles!
•
Do not attempt to cut extremely small pieces from
the tiles. Always make sure that the full surface of the
tile is on the work table. The supplied mitre guide can
be used to push the tiles through the cutter. In the
early stages of cutting in particular, the tile must
remain absolutely level to avoid the tile moving up.
•
Do not overload your tool. It is better and safer to
work within the indicated power range. Do not cut
materials other than tiles.
•
Maintain your tools carefully. Keep the tools sharp
and clean in order to work properly and safely. Fol-
low the maintenance instructions and the instruc-
tions for replacing the diamond blade.
•
Stand safely and maintain your balance. Avoid any
unnatural body angles. Remain alert and pay atten-
tion to your work. Use common sense. Do not use
the machine when you cannot concentrate or when
you are tired.
FULL-LENGTH ADJUSTABLE FENCE
Fig.1
The fence (3) enables you to cut parallel to the cutting
blade. Set up: Loosen the knobs (7) and set the required
distance. Tighten the knobs on both sides of the work
table. The markers determine the measurements (8).
3
Tabla de contenido
