Tabla de contenido
Idiomas disponibles
Idiomas disponibles
www.Securitykala.com | 031-91003037 09133648641
2) GENERAL INFORMATION
Compact electromechanical barrier suitable for enclosing private areas
justable electromechanical limit switches ensure the boom stops in the
correct position.
The emergency release for manual operation is operated by a lock with a
personalized key.
The actuator is always supplied ready for assembly on the left.
Where necessary, the opening direction can always be reversed with a
few simple operations. The foundation base mod. CBO (on request) can
be supplied to make the barrier easier to install.
need to drill additional holes.
3) TECHNICAL SPECIFICATIONS
Capacitor:
Current demand (with accessories): 1,4 A: 2.8 A
Insulation class:
Internal lubrication:
Opening time:
Boom length:
Impact reaction (Safety Edge):
Mechanical manual release:
Type of boom:
Limit switches:
24hrs:
Operating temperature range:
Actuator weight (without boom):
Flashing light:
Dimensions:
CONTROL UNIT
Accessories power supply:
Fuses:
Work time:
(*)= special supply voltages to order
4.1) FOUNDATION PLATE (Fig.B1)
4.2) ANCHOR BOLTS (Fig.B2)
5) ACTUATOR ASSEMBLY
WARNING! The barrier must be used only for entrance/exit points
intended for vehicle tra c. Pedestrians must not be allowed to pass
within range of the automated system. Make sure there is a separate
entrance/exit just for pedestrians.
The entrance/exit must be suitably signposted with the compulsory
signs illustrated in Fig.A.
WARNING: before opening the door, the spring must be decompressed
(vertical boom). The door in the cabinet must face towards the inside of the
property. Standing in the middle of the entrance, facing out, if the cabinet
is on your left, the barrier is on your left: if the cabinet is on your right, the
barrier is on your right.
The actuator is always supplied ready for assembly on the left.
6) Assembly on left (Fig. A, B, C, D).
- Balance the boom as illustrated in Fig. AB.
16
- MOOVI 30-50 - ALPHA BOM
INSTALLATION MANUAL
MOTOR
230V±10% 50Hz(*)
300W
8µF 450V (230V): 32µF 250V (110V)
F
lifetime greased
85 Nm (MOOVI 30)
250 Nm (MOOVI 50)
4s (MOOVI 30)
8s (MOOVI 50)
stop or stop and reverse
personalized key
rectangular
electric, built-in and adjustable
1200 (MOOVI 30)
600 (MOOVI 50)
da -10°C a +55°C
35,6 Kg
500 W
7) Assembly on right (Fig. AA).
- Balance the boom as illustrated in Fig. AB.
-
8) Boom assembly (Fig. D).
9) BOOM BALANCING (Fig. AB).
For Moovi 30:
WARNING! During the closing operation, the balancing spring
must never be fully compressed. Fig.AB rif.3 shows the position
for determining the minimum size that the compressed spring can be
allowed to reach with the boom in the open position (vertical).
10) OPTIONAL ACCESSORIES (Fig.E)
- Foundation base CBO
- Skirt ready assembled on boom SB
- Safety edge BIR
switches only.
MOOVI accessories (boom length limits and balancing) (Fig. AF)
For further information on installing and using the accessories, refer to the
relevant instruction manual.
11) Assembling the shearing hazard protection kit MOOVI PRM (Fig.AC)
12) Assembling the ashing light RAY X/RAY X SA (FIG.AD)
- Complete assembly and wiring as directed in instructions provided for
RAY X/RAY X SA.
13) Assembling Photocell 130 / Moovi 130 (FIG. AE).
14) ADJUSTING THE LIMIT SWITCHES (Fig. G)
----------------------------------------------------------
15) PREPARING THE ELECTRICAL SYSTEM
WARNING: before opening the door, the spring must be decompressed
(vertical boom).
dards in force. Keep mains power connections well separated from service
connections (photocells, safety edges, control devices, etc.).
WARNING! For connection to the mains power supply, use a multicore
cable with a cross-section of at least 3x1.5mm
by the regulations mentioned above (by way of example, if the cable is
not protected, it must be rated H07 RN-F or higher, while if it is protected
it must be rated at least H05 VV-F with a cross-section of 3x1.5mm
16) WIRING (FIG. F, I, J)
WARNING:
professional manner and in accordance with all regulations in force, using
appropriate materials.
BORNE
DESCRIPTION
1-2
Motor M connection (terminal 4 common, terminals 3-5
3-4-5
motor start and capacitor).
1-4
230V ashing light connection
7-8
7-9
7-10
leave jumpered.
7-11
Opening limit switch (N.C.). If not used, leave jumpered.
7-12
Closing limit switch (N.C.). If not used, leave jumpered.
13-14
24 V~output to supply photocell and other devices.
15-16
Output for barrier open light / 2nd radio channel.
17-18
Antenna receiver input (17 signal 18 braiding).
19-20
CLOSE input (N.O.) with trimmer TW=min.
JP4
1-2 channel radio-receiver board connector.
-
-
2
of the kind provided for
2
).
Tabla de contenido
