Selco Genesis Serie Instrucciones De Uso página 17

* 4 : Main parameter selection key.
- wire speed
- current
- thickness
* 5 : Potentiometer.
Permits adjustment of the Arc-Force in MMA and welding vol-
tage in MIG/MAG (if you are working in manual mode, the
absolute value of the voltage is varied; in synergic mode, a
correction is made on the synergic curve used from -9.8 Volts
(-) to +10Volts (+) with recommended value (0)).
* Display D1.
Displays figures, data.
* E1 : Encoder
Used in combination with the SETUP/parameters key (6), it
permits modification of the welding parameters selected in
the graph (7) and shown on the display (D1).
* 6 : SETUP/parameter push button.
Ensures access to the SETUP and to the welding parameter
values. If pressed within 3 seconds from the going out of the leds
(see "Operation"), ensures access to the following parameters:
0 Setup output
3 Hot-start in MMA
4 Arc-force in MMA
9 Reset of all parameters
14 Postgas in MIG (0-10s default 25)
15 Initial increase in crater filler mode
16 Crater filler % on set wire speed
17 MIG hotstart activation (1) with stainless steel
18 Burnback time
19 Softstart %
20
21 Minimum current correction or setting in MIG short
22 Int./ext. power source control selection from power
source (1) or from wire feed trolley (0). Default: 0.
In the first case, the customer is responsible for
providing the wiring.
23 MIG welding time. If set to 0 (default) the machine runs
the 2 stages regularly.
24 Deseaming enable replacing TIG.
25 WU control: default at 0 (WU off in TIG and timed in MIG);
setting at 1 (WU timed in TIG and always on in MIG)
40 Shows the software version of the 149 (machine logic)
41 Shows the software version of the 147 (trolley WF104)
Inductance in MIG.
A value from 12 (minimum inductance, arc more reac-
tive) to 100 (maximum inductance, arc softer) appears on the
display.
Frequency correction in pulsed MIG.
Permits selection of the required welding program via E1.
Short-Spray
Material Gas 0.8
Fe 100%CO2
S.01
Fe 80%Ar-20%CO2 S.05
Ss 98%Ar-2%CO2 S.09
Al 100%Ar /
AlSi 100%Ar S.17
AlMg 100%Ar S.21
CuAl
100%Ar
S.25
CuSi 100%Ar /
MCWFe 80%Ar-20%CO2 /
BFCWFe 80%Ar-20%CO2 /
RFCWFe 80%Ar-20%CO2 /
FCWSs 80%Ar-20%CO2 /
Pulsed
Ø Wire Ø Wire
1.0 1.2 1.6 0.8 1.0 1.2
S.02 S.03 S.04 / / /
S.06 S.07 S.08 P .05 P .06 P .07
S.10 S.11 S.12 P .09 P .10 P .11
S.14 S.15 S.16 / P .14
P .15
S.18 S.19 S.20 P .17 P .18 P .19
S.22 S.23 S.24 P .21 P .22 P .23
S.26
S.27
S.28
P .25
P .26
P .27
S.30 / / / P .30 /
/ S.35 S.36 / / P .35
/ S.39 S.40 / / P .39
/ S.43 S.44 / / P .43
/ S.47 S.48 / / P .47
If the program is not available, the program code is not shown
on D1.
The graph (8) on the front panel summarises this table.
Notes:
Fe carbon steel
Ss stainless steel
Al Pure aluminium
AlSi silicon aluminium (5%)
AlMg magnesium aluminium (5%)
CuAl Aluminium copper (8%)
CuSi Silicon copper (3%)
MCWFe Metallic cored filler wire
BFCWFe Basic cored filler wire
RFCWFe Rutilic cored filler wire
FCWSs Cored filler wire for stainless steel
Welding current in MMA.
Hot-Start:
Increment percentage on welding current at striking of
the arc. Facilitates starting.
The coming on of the led beside the symbol confirms the
selection.
Operation:
The machine stores the last welding step and pre-
sents it again when restarted.
* Position the start switch (I1) on " I "; the coming on of the vol-
tage warning light (L1) (green led) confirms that the plant is
under voltage.
* The display (D1) shows the control panel management soft-
ware version (e.g. 3.9) for three seconds and then the rated
current of the power source; at this moment it is possible :
- enter the SETUP mode by pressing the SETUP/para-meter
push button (6);
- or go on with the welding (or with the parameter modifica-
tion).
* If selected, the SETUP mode is confirmed by a central "0" on
the display (D1).
- Rotate the encoder (E1), the display (D1) shows the num-
bers corresponding to the parameters in sequence, (see
SETUP/parameter push button); stop at the desired parame-
ter and push the SETUP/parameter push button (6).
With parameter (9) of SETUP all the modifications made in
the SETUP mode are cancelled and the standard values set
by SELCO are restored.
- The number on the display (D1) is replaced by the value of
the parameter that can be modified through the potentio-
meter (E1).
* If it is necessary to modify the values of the welding parame-
ters of the diagram (7), proceed as follows:
- Wait three seconds after the leds on the panel have gone
out.
1.6
- Select the required welding procedure via (2).
/
- Procedure selected (MIG P).
P .08
- Select main PARAMETER TYPE required via (4).
P .12
P .16 - Select program (P) setting mode via (6).
P .20
- Rotate E1 to select the required program, chosen from the table
P .24
given on the front panel.
P .28
- If you have selected the MMA or TIG procedure, adjust F1 to
/
vary the welding current value.
P .36
P .40
The machine is always ready to weld and its state
P .44
is defined by all the leds that are on the panel.
P .48
17