Commissioning; Qlwldo Frq¿Jxudwlrq; End-Product - SOMFY Chronis io Manual Del Usuario

Chronis io

5. COMMISSIONING

Before commissioning the Chronis io, each motor must have been programmed by an installer
using an individual io control point or a setting tool and the end limits must have been adjusted.
This manual only describes commissioning using a Smoove io type individual io control point
To perform commissioning using a different io control point, refer to the corresponding manual.
1
The backlighting of the Chronis io switches off automatically after the device has been
inactive for a few seconds.
The Chronis io display switches off automatically after the device has been inactive for a few
minutes (time differs depending on mode).
 %DWWHU\ LQVWDOODWLRQ DQG UHSODFHPHQWV
Never use rechargeable batteries.
Replace the batteries when the ( ) symbol appears on the screen.
If there is no power supply for an extended period of time (> 2 min) (batteries out of charge or
removed), the date and time will have to be reset. The other settings are saved.
- Unclip the Chronis io from the wall mount (see section
Clipping on and unclipping the Chronis io from its wall
mount).
- Remove the used batteries from the compartment in the
back of the Chronis io.
- ,QVHUW  W\SH $$$ /5 EDWWHULHV XQGHU WKH ÀDS IROORZLQJ
the polarity indicated.
- When the batteries are inserted, the screen lights up.
Batteries or accumulators have to be separated
from other types of waste and must be recycled
through your local treatment and recycling system.
 ,QLWLDO FRQ¿JXUDWLRQ
The IDFWRU\ FRQ¿JXUDWLRQ of the Chronis io is as follows:
‡ in standard end-product control mode: "
‡ with the standard radio frame repetition setting: "
‡ in control mode for non-self-powered motor: "
If the factory presettings are suitable for the installation, go on to the next section.
'XULQJ LQLWLDO FRQ¿JXUDWLRQ RI WKH &KURQLV LR LW LV SRVVLEOH WR VHW WKH SDUDPHWHUV DV D IXQFWLRQ RI WKH
controlled end-product or end-products by selecting a control mode for the end-product, a radio frame
UHSHWLWLRQ VHWWLQJ DQG D FRQWURO PRGH VSHFL¿F WR VHOISRZHUHG PRWRUV
&RQWURO PRGHV IRU HQGSURGXFWV
4 control modes are available and you can change between these depending on the controlled

end-product:

MODE STD : 1
‡ " ": To control all io-homecontrol
garage doors, gates.
MODE DIM : 2
‡ " ": Recommended for the control of adjustable level lighting and heating.
MODE TILT1 : 3
‡ " ": Recommended for the control of exterior venetian blinds and roller shutters with
adjustable slats.
MODE TILT2 : 4
‡ " ": Recommended for the control of interior venetian blinds.
5DGLR IUDPH UHSHWLWLRQ VHWWLQJ
'HSHQGLQJ RQ KRZ WKH LQVWDOODWLRQ LV FRQ¿JXUHG LW LV SRVVLEOH WR LQFUHDVH WKH QXPEHU RI UDGLR IUDPH
repetitions (in the automatic and simulated presence modes). 5 settings are available: "
:
RADIO 2
1 repetition, " " for 2 repetitions, "
: 5" for 5 repetitions.
RADIO
"
The higher the number of repetitions, the shorter the battery life is.
&RQWURO PRGHV IRU VHOISRZHUHG PRWRUV
If a self-powered motor is controlled by the Chronis io: choose the option "
4
".
MODE STD : 1
: ".
RADIO 1
SOLAR MOTOR : NO
®
end-products, for example roller shutters, windows,
: 3" for 3 repetitions, "
RADIO
Copyright © 2013 Somfy SAS. All rights reserved.
2 x LR03
AAA 1,5 V
".
RADIO
: 4" for 4 repetitions and
RADIO
SOLAR MOTOR : YES
.
:
1
" for
".