Mounting Instruction - Chicago Pneumatic CP80015 Manual Del Operador

EN English
1. Technical Data (See figure 1.)
Technical Data Weight
Unit
CP80015
CP80020
CP80021
CP80030
CP80031
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
2. Machine type(s)
• A Trolley jack is a device to lift a vehicle up to for accessibility during repair and maintenance.
• A Jack is only a lifting device and should never be used for transporting and/or loading a vehicle. Lifting a vehicle with person inside is
prohibited. Moving the jack with load is prohibited. No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.

3. Mounting instruction

WARNING
Make sure every parts are fixed and tightened.
• Remove the transportation lock on the lever support. (Fig.02). Push the lever support down (1/2) and remove the transport lock (3/4).
• At first remove the hexagon screw SW10 (Fig.03(1)) at the side of the lower lever rod and put the upper and lower lever rod together before
securing the connection with the hexagon screw (Fig.03(2/3/4).
• Now attach the lever rod to the lifting device. For this purpose remove the hexagonal screw SW17 at the support of the lifting device
(Fig.04(1)) and place the lever rod into the support (Fig.04(2)). Fasten the screw again (Fig.04(3/4)).
• Before using the trolley jack it is necessary to de-aerate the hydraulic circuit (see section 6).
Caution
Working area of 1 m must be kept free both in front of and behind the machine while it is in operation so that it is always
easily accessible.
Purge air from the hydraulic system:
• Open the discharge valve by turning the lever rod anticlockwise whilst simultaneously pumping with the lever (5-6 times).
• Afterwards, pump the jack up to its maximal height before lowering it again. The hydraulic system is de-aerated.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
4. Operation
Caution
Please position the trolley jack underneath the lifting points of the vehicle.
• Make sure that no person stays in the car that will be lifted. Turn off the engine and put on the handbrakes of the car. Use wedges to prevent
the car from moving (Fig.05(1)). Do not get into the car and do not turn the engine on.
• Always position the lifting jack in such a way that it cannot be operated from underneath the car (Fig.05(4)).
• Always make use of the car manual in order to identify the correct lifting points of the vehicle.
• Use the lever rod or the foot pedal to bring the lifting device to the desired height (Fig.05 (2)). Make sure that the hydraulic valve is closed.
For this purpose it is necessary to fasten the lever rod clockwise.
Please note, that the foot pedal is mainly used to bridge the no-load stroke.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
• The lifting devices are provided with an overload valve, which has been adjusted by the manufacturer. This valve must never be readjusted.
• In order to lower the load turn the lever rod slowly anticlockwise (Fig.05(3)).
• It is necessary that the operator can watch the lifting device and the load during all movements.
WARNING
Never use the lifting jack in order to move the car or to leave it lifted. Always use chassis stands (Fig.05(5)).
WARNING
When not using the trolley jack the piston / lifting arm must be pulled in.
WARNING
It is not allowed to work under the raised load until it is secured by suitable means.
WARNING
The operator shall be provided with all necessary information about training and about pumping and translating forces.
Lifting capacity
[kg] [kg]
50.5 1500
39.4 2000
39.8 2000
45 3000
46 3000
CP80015/CP80020/CP80021/CP80030/CP80031
Hydraulicioil Quantity A B
[l] [mm] [mm]
0.21 530 70
0.29 430 75
0.29 430 75
0.22 455 95
0.22 455 95
C D D2 E F
[mm] [mm] [mm] [mm] [mm]
600 920 2140 153 282
505 750 1960 150 270
505 760 1965 145 277
550 860 2050 160 257
550 860 2050 160 257
Trolley jack
G
[mm]
382
375
380
375
375