Operation - EINHELL TH-TS 1725 U Manual De Instrucciones

Anleitung_TH_TS_1725_U_SPK8__ 24.09.12 14:53 Seite 35
chip extraction system to the extractor adapter
(16).
To dismantle, proceed in reverse order.
n
Important.
The saw blade guard (2) must always be
lowered over the workpiece before you begin
to cut.
7.4 Changing the table insert (Fig. 17-18)
To prevent increased likelihood of injury, the table
n
insert (6) should be changed whenever it is worn
or damaged.
Take off the saw blade guard (2) (see 8.3).
n
Remove the 2 countersunk head screws (29).
n
Take out the worn table insert (6).
n
Fit the replacement table insert by following the
n
above in reverse.
7.5 Adjusting the splitter (Fig. 19-20)
Important. Pull out the power plug.
n
The setting of the saw blade (5) has to be
n
checked each time after changing the saw blade.
Set the blade (5) to max. cutting depth, move to
n
0° position and lock in place (see 9.2).
Dismantle the saw blade guard (2) (see 8.3).
n
Take out the table insert (6) (see 8.4).
n
Slacken the fixing screw (30).
n
Push up the splitter (4) until the gap between the
n
saw table (1) and the upper edge of the splitter
(4) equals approx. 10 cm.
The distance between the blade (5) and the
n
splitter (4) should be max. 5 mm. (Fig. 20).
Retighten the fixing screw (30) and mount the
n
table insert (6) (Fig. 8.4).
Remount the blade guard (2) (see 8.3).
n
7.6 Fitting/changing the blade (Fig. 21)
Important. Pull out the power plug and wear
n
protective gloves.
Dismantle the saw blade guard (2) (see 8.3).
n
Remove the table insert (6) by undoing the two
n
countersunk head screws (see 8.4).
Undo the nut with a wrench (size 24) on the nut
n
itself and a second fork wrench (size 10) on the
motor shaft to apply counter-pressure.
Important. Turn the nut in the direction of
n
rotation of the saw blade.
Take off the outer flange and pull the old saw
n
blade off the inner flange by dropping the blade at
an angle.
Clean the saw blade flange thoroughly with a wire
n
brush before fitting the new saw blade.
Mount and fasten the new saw blade in reverse
n
order.
Important. Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the table insert (6) and the saw
n
blade guard (2) (see 8.3, 8.4)
Check to make sure that all safety devices are
n
properly mounted and in good working condition
before you begin working with the saw again.

8. Operation

8.1.1 ON/OFF switch (Fig. 22/Item 11)
To turn the saw on, press the green button "I" .
n
Wait for the blade to reach its maximum speed of
rotation before commencing with the cut.
To turn the equipment off again, press the red
n
button "0".
8.1.2 Overload cut-out (Fig. 45)
The motor of this appliance is protected against
overload by an overload switch (A). If the rated
current is exceeded, the overload switch (A) switches
the appliance off. After a short cooling-off phase, the
appliance can be switched back on by pressing the
overload switch (A).
8.2. Cutting depth (Fig. 22).
Turn the hand wheel (8) to set the blade (5) to the
n
required cutting depth.
Turn anti-clockwise:
larger cutting depth
Turn clockwise:
smaller cutting depth
8.3. Setting the angle (Fig. 22)
Undo the fixing handle (9).
n
Turn the handle to set the desired angle on the
n
scale.
Lock the fixing handle again in the required angle
n
position.
8.4 Parallel stop
8.4.1. Stop height (Fig. 23-26)
The stop rail (e) for the parallel stop (7) has two
n
different guide faces (high and low).
For thick material you must use the stop rail (e) as
n
shown in Fig. 25, for thin material (with a
workpiece thickness of less than 25 mm) you
must use the stop rail as shown in Fig. 26.
GB
35