Safety Instructions For Specific Circular Saws - Festool HK 55 EQ Manual De Instrucciones

controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source and/
or battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the pow-
er tool's operation. If damaged, have the power
tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions tak-
ing into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h. Keep handles dry, clean and free from oil and
grease. Slippery handles do not allow for safe
handling and control of the tool in unexpected
situations.
5 SERVICE
a. Have your power tool serviced by a qualified re-
pair person using only identical replacement
parts. This will ensure that the safety of the pow-
er tool is maintained.
Safety instructions for specific circular
Cutting procedures
DANGER!
a.
ting area and the blade. Keep your second hand
on auxiliary handle, or motor housing. If both
hands are holding the saw, they cannot be cut by
the blade.
b. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below
the workpiece.
c. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade
saws
Keep hands away from cut-
teeth should be visible below the workpiece.
d. Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform. It is important to sup-
port the work properly to minimize body
exposure, blade binding, or loss of control.
e. Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting tool may contact hidden wiring. Contact
with a "live" wire will also make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
f. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut
and reduces the chance of blade binding.
g. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the
saw will run off-centre, causing loss of control.
h. Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were spe-
cially designed for your saw, for optimum perfor-
mance and safety of operation.
i.Wear suitable protective equip-
ment such as ear protection,
safety goggles, a dust mask for
work which generates dust, and
protective gloves when working
with raw materials and when
changing tools.
Kickbacks causes and related warnings
– kickback is a sudden reaction to a pinched,
jammed or misaligned saw blade, causing an un-
controlled saw to lift up and out of the workpiece
toward the operator;
– when the blade is pinched or jammed tightly by
the kerf closing down, the blade stalls and the
motor reaction drives the unit rapidly back to-
ward the operator;
– if the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can
dig into the top surface of the wood causing the
blade to climb out of the kerf and jump back to-
ward the operator.
Kickback is the result of saw misuse and/or incor-
rect operating procedures or conditions and can be
avoided by taking proper precautions as given be-
low.
a. Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forc-
es. Position your body to either side of the
blade, but not in line with the blade. Kickback
could cause the saw to jump backwards, but
9