Cleaning And Maintenance - Steinberg Systems SBS-FZ 3000/3GM Manual De Instrucciones

• REGULAR INSPECTIONS (recommended as monthly):
• Check chain wear and tear.
• Check the wear and tear of the hooks: level of wear and tear, damage, enlargement of the hook slit, shank bend
or hook deviation.
• Check fastening of the hooks.
• Clean and lubricate the chains.
POSSIBLE HAZARDS DURING USE
The hazards that can occur during use of the machine are mechanical hazards. The mechanical hazard occurs in situations in
which injuries can result from mechanical impact of various elements, e.g. machine parts, tools, etc. on people.
The basic mechanical hazards include squeezing, crushing, cutting, pulling in or catching; impact; puncture; abrasion; as well
as slipping and stumbling.
These hazards can occur both during normal machine operation and as a result of irregularities in machine operation. These
irregularities might result in machine failure.
The mechanical hazards can result from: moving machines, transported loads, moving elements, sharp/rough elements,
dropping elements/loads, slippery uneven surfaces, limited space, location of the work station in relation to the ground
(work at heights and in depths).
VII. CLEANING AND MAINTENANCE
The chain hoist must be cleaned regularly. After completion of work, remove all dirt from the chains and the machine itself.
The chains, hooks, hinges and hook latches must be regularly lubricated with grease. When the load chain is rusted, the
rust must be removed and the chain greased. If rust cannot be removed, the load chain must be replaced. All and any hoist
maintenance and inspection activities must be carried out by a trained and qualified employee. They cannot be conducted by
a person without proper experience and knowledge.
VIII. GENERAL MACHINE DIAGRAM
1 2 3 4 5 6 7 8 10 11
EN
22 23 24 25 26
424344 45
38 39 40 41
12 13 14 15 16 17 18 19 20
34 35 36
27
28 29 30 31 32 33
47
46
12
Rev. 25.03.2019
1 Wheel housing
2 Nut
3 Arbor
4 Wheel
5 Hub washer
6 Ratchet wheel
7 Ratchet
8 Ratchet arbor
9 Plate left side
10 Spring
11 Arbor
12 Rivet
13 Rivet
14 Upper clamp
15 Shaft arbor
16 Support
IX. REGULAR CONTROL OF THE MACHINE
Regularly check the machine for signs of damage. If it should be damaged, please stop using it immediately and contact your
21
customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the machine).
• if relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give a detailed and
precise description of the matter.
The more detailed your information, the better customer service will be able to solve your problem rapidly and efficiently!
CAUTION: Never open the machine without the authorization of your customer service. This can lead to a loss of warranty!
The machine does not contain any substances harmful to one's health, its parts are made of metal. After withdrawal from
37
service, the machine must be transferred to a scrap yard. Observe the environmental protection regulations of the given
country.
Rev. 25.03.2019
17 Plate right side 33
18 Bearing load ring 34
19 Spindle transmission 35
20 Transmission 36
21 Bent plate 37
22 Chain 38
23 Break 39
24 Roller 40
25 Arbor 41
26 Stripper 42
27 Nut 43
28 Hub suspension 44
29 Hub arbor 45
30 Chain gear wheel 46
31 Ring 47
32 Roller
13
Nut
Clutch
Rack
Bearing load ring
Lid
Nut
Washers
Screws
Lower clamp
Wheel shaft
Needle
Hook
Latch
Roller
Load chain
EN