Sony RM-V210 Manual De Instrucciones página 2

Setting the Code
Follow the steps 1 and 2 below for each component you plan to use
with the Commander.
Step 1: Entering the Code Number
1 See the supplied "Component code
numbers", and find the four-digit code
number for the desired component.
If more than one code number is listed, use
the number that's listed first.
For example, if you're setting up a Sony
TV, you would use the code number 8201.
If your component isn't listed, see
"Searching for the Correct Code."
2 Press SET more than two
seconds.
The SET indicator lights up.
3 Press the button of the
component that you want to
set up.
The SET indicator lights up.
4 Press the Number buttons to enter the four-digit
component code number.
5 Press ENTER. The SET indicator turns off. If the SET
indicator flashes five times before lighting up, it
means that the setup is incomplete. Confirm the
component code number and start over from Step 4.
If the code setting is not finished properly
If you do not input anything into the Commander within 20 seconds
between each step, or if you press SET while setting the component
code, the setup procedure will be canceled.
Start over from Step 2.
Step 2: Checking if the Code Number Works
1 Power on the component you want to set up.
2 Aim the Remote Commander at the component and press a button
to check if that button works.
For example, press the POWER button to see if it works on your
component .
3 Check that the other buttons of the Commander is operating the
corresponding functions of the component.
You can write down the code number on the label inside the
battery compartment lid.
If the Commander Doesn't Seem to Be Working...
• First, try repeating these setup procedures using the other codes
listed for your component (see the supplied "Component Code
Numbers").
• If – after trying all the codes listed for your component – you still
cannot get the Commander to work properly, try the search
method described in "Searching for the Correct Code."
POWER
SET
TV VCR CBL DVD
1 2 3
4 5 6
7 8 9
0
ENTER
VOL CH
INPUT
PIP
SLEEP
INFO
MUTING RECALL
SET
SET
SET
TV VCR CBL DVD
ENTER
Searching for the Correct Code
You can find a code number available for a
component that doesn't have one in the
supplied "Component code numbers."
Before starting the Search function
2
Set each component to the following status so
that the Search function works effectively.
3
TV, DVD Home Theater: Power-on
Other components: Power-off
4
* If any of these components are assigned to any
5
of the Component Select buttons, you can set a
component code using the Search function.
1 Press SET more than two seconds. The SET indicator lights up.
2 Press the Component Select button for the desired component.
The SET indicator lights up.
3 Press CH + or CH – and POWER in turn until the component
reacts as follows:
TV, DVD Home Theater: Powers off
Other components: Powers on
Press CH + to go to the next code number.
Press CH – to go back to the previous code number.
The SET indicator flashes once after the numbers have turned one
cycle.
One cycle means, for example, that the commander finishes
searching all the component code numbers allocated to the
component.
4 Press ENTER.
The SET indicator and the Component button turn off.
If the SET indicator flashes five times before turning off, it means
that the setup is incomplete. Start over from Step 3.
If the component does not operate properly, repeat steps 1 to 4 and
search for another code.
If you still cannot get the Commander to work properly, see
"Troubleshooting."
Operating a Component
1 Press the button of the desired component on the Commander.
TV VCR CBL
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
See "Remote Button Descriptions" for complete descriptions of the
buttons on the Commander.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the Commanders
supplied with your components.
• Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to the
functions of the components themselves. For example, if your TV
does not have a MUTING function, MUTING on this Commander
will not function with your TV.
• Some functions of the component may not work with this
Commander.
• If your cable box can control volume, be sure to set its volume
switch to a medium position. If the volume on the cable box is
turned down completely, you will not be able to adjust your TV's
volume with the Commander.
DVD
1
3
SET POWER
2
TV VCR CBL DVD
1 2 3
4 5 6
7 8 9
4
0
ENTER
VOL CH
INPUT
3
PIP
SLEEP
INFO
MUTING RECALL