Functional Description; Storing Accessories - Makita 2704N Manual De Instrucciones

13. Always make sure that sub guard is down and
flat against saw-table before plugging in the
tool.
14. Inspect extension cords periodically and
replace if damaged.
15. (For European countries only)
Use only saw blades recommended by the
manufacturer and which conform to EN847-1.
INSTALLATION
Positioning table saw
► Fig.1: 1. Hole diameter 8 mm
► Fig.2: 1. 6 mm Std. washer 2. No.10 wood screw 40
mm min. length
► Fig.3: 1. 6 mm Std. washer 2. 6 mm Mounting bolt
& Nut tighten securely
Locate the table saw in a well lit and level area where
you can maintain good footing and balance. It should
be installed in an area that leaves enough room to
easily handle the size of your workpieces. The table
saw should be secured with four screws or bolts to the
work bench or table saw stand using the holes provided
in the bottom of the table saw. When securing the table
saw on the work bench, make sure that there is an
opening in the top of the work bench the same size as
the opening in the bottom of the table saw so the saw-
dust can drop through.
If during operation there is any tendency for the table
saw to tip over, slide or move, the work bench or table
saw stand should be secured to the floor.

Storing accessories

► Fig.4: 1. Miter gauge
► Fig.5: 1. Rip fence 2. Push stick 3. Anti-kickback
pawls
The miter gauge, saw blade and wrenches can be
stored on the left side of the base. Also the rip fence,
push stick, and anti-kickback pawls can be stored at the
right side of the base.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and unplugged before adjusting or
checking function on the tool.
Blade guard
WARNING:
guard. An exposed blade as a result of defeated
guarding may result in serious personal injury during
operation.
WARNING:
guard is damaged, faulty or removed. Operation of
the tool with a damaged, faulty or removed guard may
result in serious personal injury.
► Fig.6: 1. Blade guard 2. Sub guard
When cutting, push the workpiece toward the blade
with the lower edge of the sub guard contacting with the
main table. As the workpiece is fed, the blade guard and
the sub guard goes over the edge of the workpiece.
In the interest of your personal safety, always maintain
the blade guard and sub guard in good condition. Any
irregular operation of the blade guard and sub guard
should be corrected immediately. Check to assure that
the blade guard and the sub guard are down and the
lower edge of the sub guard contacts with the main
table when the workpiece is not fed.
If the see-through parts become dirty, or sawdust
adheres to them in such a way that the blade and/or
workpiece is no longer easily visible, unplug the tool
and clean the see-through parts carefully with a damp
cloth. Do not use solvents or any petroleum-based
cleaners because this may cause damage to the parts.
If see-through parts become discolored through age or
UV light exposure, contact a Makita service center for
a new parts. DO NOT DEFEAT OR REMOVE BLADE
GUARD AND SUB GUARD.
Adjusting the depth of cut
► Fig.7: 1. Handle
The depth of cut may be adjusted by turning the handle.
Turn the handle clockwise to raise the saw blade or
counterclockwise to lower it.
NOTE: Use a shallow depth setting when cutting thin
materials in order to obtain a cleaner cut.
Adjusting the bevel angle
► Fig.8: 1. Lock lever 2. Arrow pointer 3. Handwheel
Loosen the lock lever counterclockwise and turn the
handwheel until the desired angle (0° - 45°) is obtained.
The bevel angle is indicated by the arrow pointer.
After obtaining the desired angle, tighten the lock lever
clockwise to secure the adjustment.
CAUTION:
After adjusting the bevel angle, be
sure to tighten the lock lever securely.
12 ENGLISH
Never defeat or remove the blade
Never use the tool if the blade