Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Loading tracks via the wireless LAN
! To load tracks from sources other than mobile devices, see the oper-
ating instructions on the included CD-ROM.
! For instructions on loading tracks from a computer via wireless LAN,
also see "Playback connected to a LAN" in the Operating Instructions
of rekordbox (Mac/Windows).
1 Launch rekordbox on the mobile device and establish
the link.
2 Operate rekordbox on the mobile device to select the
track.
3 Operate rekordbox on the mobile device to select the
deck on which the track is to be loaded, then tap.
Track loading starts. The jog dial indicator on the deck on which the
track is being loaded flashes.
Once playback is possible, the jog dial indicator stops flashing, remain-
ing lit, the track name is displayed on the main unit display and playback
starts (by factory default).
4
En
Outputting sound
Set the volume of the power amplifiers connected to the [MASTER OUT
1] and [MASTER OUT 2] terminals to an appropriate level. Note that very
loud sounds will be output if the volume is set too high.
When playing tracks via wireless LAN, playback may become impos-
sible due to deterioration of the communication conditions. In this
case, loop playback begins automatically and [EMERGENCY LOOP] is
displayed on the main unit display.
When communications conditions recover, the [EMERGENCY LOOP]
display turns off. Press the [AUTO BEAT LOOP] control at this time to
cancel looping.
To output the sound of channel 1 [CH 1]
To output the sound of [CH 2] (channel 2), replace [CH 1] with [CH 2]
and [DECK1] with [DECK2] in the procedure below.
1 Switch the [DECK1, PHONO1/LINE1] selector switch
for [CH 1] to [DECK1].
2 Press the [MASTER] button at the center of this unit.
Set so that the [MASTER] button is off.
! When the [MASTER] button is off, the audio level input to [CH 1] and
[CH 2] is displayed on the [LEVEL] indicator.
3 Turn the [CH 1] [TRIM] control clockwise.
Adjusts the audio level input to the [CH 1] terminal.
The [LEVEL] indicator lights when sound is properly being input to
[CH 1].
Adjust the [TRIM] control so that the orange indicator lights where the
track's volume is highest (at the climax, etc.)
Be careful that the red indicator does not light, or the sound could be
distorted.
4 Move the [CH 1] channel fader to the back side.
The level of the sound output from the [CH 1] terminals is adjusted.
5 Set the crossfader.
Switch the channel whose sound is output from the speakers.
— Left edge: The [CH 1] sound is output.
— Center position: The sound of [CH 1] and [CH 2] is mixed and
output.
— Right edge: The [CH 2] sound is output.
6 Press the [MASTER] button at the center of this unit.
Set so that the [MASTER] button is lit.
! When the [MASTER] button is lit, the audio level output from the
[MASTER OUT 1] and [MASTER OUT 2] terminals is displayed on
the [LEVEL] indicator.
7 Turn the [MASTER LEVEL] control clockwise.
Sound is output from the speakers.
The [LEVEL] indicator lights.
Adjust the [MASTER LEVEL] control so that the orange indicator lights
where the track's volume is highest (at the climax, etc.)
Be careful that the red indicator does not light, or the sound could be
distorted.
Additional information
Read Software end user license agreement carefully before installing
rekordbox (Mac/Windows) and the driver software.
Read "Cautions on installing the software" in the operating instructions
on the included CD-ROM before installing rekordbox (Mac/Windows)
and the driver software on the computer.
Software end user license agreement
This Software End User License Agreement ("Agreement") is between
you (both the individual installing the Program and any single legal
entity for which the individual is acting) ("You" or "Your") and PIONEER
CORPORATION ("Pioneer").
Tabla de contenido
