Important Safety Instructions - Makita AN621 Manual De Instrucciones

ENGLISH
1 Compressor air output per
minute
2 Nailing frequency (times/min.)
3 Pneumatic tool oil
4 Adjuster
5 Change lever
6 Plastic collated coil
7 Wire collated coil
8 Door
9 Magazine cap
10 Lever
SPECIFICATIONS
Model
Air pressure .................. 0.44 – 0.83 MPa (4.4 – 8.3 bar)
Applicable length
Wire welded nails ................................45 mm – 65 mm
Plastic sheet collated nails ..................50 mm – 65 mm
Nail capacity ............................................. 200 – 300 pcs.
Min. hose diameter .............................................. 6.5 mm
Pneumatic oil ....................................................Turbine oil
Dimensions (L x H x W) .... 310 mm x 305 mm x 133 mm
Net weight .............................................................. 2.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2" x 4" housing.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
WHEN USING THIS
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and main-
tenance of the tool, read this instruction manual
before using the tool.
• Always wear safety glasses to protect your eyes
from dust or nail injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
• Wear hearing protection to protect your ears
against exhaust noise and head protection. Also
wear light but not loose clothing. Sleeves should
be buttoned or rolled up. No necktie should be
worn.
• Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when
under the influence of alcohol, drugs or the like.
Explanation of general view
11 Graduation
12 Coil support plate
13 Slot
14 Magnet
15 Feeder body
16 Air socket
17 Air fitting
18 Trigger
19 Contact element
20 Continuous nailing
21 Trigger lock
AN621
ENB067-2
TOOL, BASIC SAFETY
OF PERSONAL INJURY,
22 Exhaust cover
23 Small rod
24 Ejection port
25 Hook
26 Cap
27 Drain cock
28 Air filter
29 Oiler
30 Pneumatic oil
General Tool Handling Guidelines:
1. Always assume that the tool contains fasteners.
2. Do not point the tool toward yourself or anyone whether it contains fasteners or not.
3. Do not activate the tool unless the tool is placed
firmly against the workpiece.
4. Respect the tool as a working implement.
5. No horseplay.
6. Do not hold or carry the tool with a finger on the
trigger.
7. Do not load the tool with fasteners when any one
of the operating controls is activated.
8. Do not operate the tool with any power source
other than that specified in the tool operating/
safety instructions.
• An improperly functioning tool must not be used.
• Sparks sometimes fly when the tool is used. Do not
use the tool near volatile, flammable materials such
as gasoline, thinner, paint, gas, adhesives, etc.;
they will ignite and explode, causing serious injury.
• The area should be sufficiently illuminated to
assure safe operations. The area should be clear
and litter-free. Be especially careful to maintain
good footing and balance.
• Only those involved in the work should be in the
vicinity. Children especially must be kept away at
all times.
• There may be local regulations concerning noise
which must be complied with by keeping noise lev-
els within prescribed limits. In certain cases, shut-
ters should be used to contain noise.
• Do not play with the contact element: it prevents accidental discharge, so it must be kept on and not
removed. Securing the trigger in the ON position is
also very dangerous. Never attempt to fasten the
trigger. Do not operate a tool if any portion of the
tool operating controls is inoperable, discon-
nected, altered, or not working properly.
• Operate the tool within the specified air pressure of
0.44 – 0.83 MPa (4.4 – 8.3 bar) for safety and longer
tool life. Do not exceed the recommended max.
operating pressure of 0.83 MPa (8.3 bar). The tool
should not be connected to a source whose pres-
sure potentially exceeds 1.37 MPa (13.7 bar).
7