Specifi Cations - Panasonic RP-WF6000 Instrucciones De Funcionamiento

Troubleshooting guide
Problem Possible cause and suggested remedy
Sound is broken y Change the placement of the transmitter. Stay within the range of the transmitter
(noise may be ( page 11).
heard too).
y The headphones' OPR lamp dims. Sound is distorted, intermittent or there is
excessive background noise during use (
● The rechargeable battery has run down. Recharge it or replace the alkaline dry cell
batteries with new ones.
y Make sure that there is no other equipment that uses the 2.4 GHz radio frequency
band such as wireless equipment or microwaves near the transmitter or headphones
( page 3).
y Set the most appropriate frequency (
frequency]).
There is excessive y If the transmitter is connected to the headphone jack, turn the volume up on the
background noise.
connected equipment (
y The headphones' OPR lamp dims. Sound is distorted, intermittent or there is
excessive background noise during use. (
● The rechargeable battery has run down. Recharge it or replace the alkaline dry cell
batteries with new ones.
y Make sure that there is no other equipment that uses the 2.4 GHz radio frequency
band such as wireless equipment or microwaves near the transmitter or headphones
( page 3).
y Set the most appropriate frequency (
frequency]).
Audio cannot be y When the input audio (analog only) continues to be very low for more than 5 minutes
heard while analog
(approximately), the radio waves being emitted from the transmitter may stop (
is selected. page 13).
In this case perform the following steps.
1. Switch the ATT control on the transmitter to "0 dB" (
If audio still cannot be heard
2. Increase the volume level on the equipment connected to the analog input and
decrease the volume level on the headphones.
No surround effect. y Set "CINEMA", "MUSIC" or "VOICE" on the transmitter's SURROUND button
( page 14).
y The input audio signal is not multi-channel. There is no surround effect when playing
a monaural source (
y You have selected "PCM" for the audio digital output setting on the DVD player
The DOLBY
(includes game machines).
DIGITAL lamp
● Select "Dolby Digital/PCM" or "Dolby Digital" if the DVD player has an internal
does not light.
Dolby Digital decoder.
y You are playing a signal that is not recorded in DOLBY DIGITAL format.
y The chapter being played is not DOLBY DIGITAL format.
The DOLBY PRO
y You have set the transmitter's SURROUND button to "OFF" (
LOGIC II lamp
y There are no analog input signals, digital input signals (PCM), Dolby Digital 2-
does not light.
channel signals or MPEG-2 AAC 2 channel signals being input.
y You have set the transmitter's SURROUND button to a setting other than "OFF"
The DOLBY PRO
LOGIC II lamp ( page 13).
lights.
y There are analog input signals, digital input signals (PCM), Dolby Digital 2-channel
signals or MPEG-2 AAC 2 channel signals being input.
16
16
page 8).
page 14 [Setting the most appropriate
page 10).
page 8).
page 14 [Setting the most appropriate
page 10).
page 14).
page 13).
Problem Possible cause and suggested remedy
The DTS lamp y You have selected "OFF" for the DVD player's DTS digital output setting
does not light. ( page 10).
● Refer to the operating instructions for the DVD player and set the DTS digital
output setting on the DVD player to "ON".
y You are playing a signal that is not recorded in DTS format.
y The chapter being played is not DTS format.
y The DVD player is not DTS compatible (
● Use a DTS compatible DVD player.
The MPEG-2 AAC y The television's output setting is set to "PCM".
lamp does not
● Refer to the operating instructions for the television and set the television to output
light.
MPEG-2 AAC signals.
Cannot select dual y Connect the analog audio output of the equipment to the LINE IN terminal and select
audio (MAIN/SUB)
the desired sound on the connected equipment (
when input is digital.
Cannot charge.
y The OPR/CHARGE lamp on the transmitter does not glow red (
● Check that the headphones are put on the transmitter correctly.
y A dry cell battery is inserted.
● Be sure to insert the supplied nickel-metal hydride rechargeable battery.
y A nickel-metal hydride rechargeable battery other than the supplied one is inserted.
● Insert the supplied nickel-metal hydride rechargeable battery or a dedicated
replacement battery RP-BP6000 (optional). (
y There is dirt on the charging terminals of the headphones or the transmitter
( page 8).
● Remove it gently with a cotton swab etc.
y A noise signal is being received from the connected equipment.
Radio wave output
does not stop. ● Turn off the power on the connected equipment.
Specifications
Transmitter (RP-WF6000T)
Decoder function
Dolby Digital, Dolby Pro Logic II, DTS, MPEG-2 AAC
Surround function OFF, MUSIC, CINEMA, VOICE
Modulation method
DSSS (Direct-Sequence Spread Spectrum)
Transmitting frequency 2.412 GHz to 2.462 GHz
Transmitting distance
Approximately 30 meters (98.4 ft.)
Frequency response 10 Hz to 24,000 Hz
Distortion factor Less than 0.1 % (1 kHz)
Audio input
Optical digital input (TOS Link type) x 2
Analog input (RCA type, left/right) x 1
Audio output
Optical digital output (TOS Link
type)(Pass through) x 1
Power supply DC 9 V (using supplied AC adaptor)
Dimensions (W x H x D)
178 mm x 105.5 mm x 161.5 mm
(7 in. x 4-1/8 in. x 6-3/8 in.)
Mass Approx. 355 g (12.5 oz.)
page 10).
page 12).
page 7).
page 6)
Headphones (RP-WF6000H)
Frequency response 10 Hz to 24,000 Hz
Power supply
Supplied rechargeable nickel-metal hydride
battery (1 pair) or commercially available "LR6,
AA" alkaline dry cell batteries (2) (not included)
Mass Approx. 380 g (13.4 oz.) (Including supplied
rechargeable nickel-metal hydride battery)
Transmitter and Headphones in the
Charging Position
Dimensions (W x H x D)
202 mm x 244 mm x 161.5 mm (7-15/16 in. x
9-5/8 in. x 6-3/8 in.) (Vertical position)
202 mm x 115 mm x 270 mm (7-15/16 in. x
4-1/2 in. x 10-5/8 in.) (Horizontal position)
AC Adaptor (RFX5726)
Input AC 100 - 240 V, 50/60 Hz
Output DC 9 V, 2 A
Power consumption 30 W
Power consumption of the AC adaptor in
standby mode
(when connected to the transmitter)
approx. 1.8 W
Note
Specifi cations are subject to change without notice.
17
17