Troubleshooting; Technical Data; Motor; Mower - Sabo JOHN DEERE 36-EL Manual Del Operador

17 TROUBLESHOOTING

Fault Possible cause
No power supply.
If the motor does not
start 5 seconds after
the unit is started
Power cable damaged.
Cutting height has been
set too low (grass is too
high and blocks the
starting of the motor).
Too much grass waste in
the housing.
Extreme vibration
Blade blunt.
Unclean cut, lawn is
yellow
Cutting height too low.
Mowing too fast.
Insufficient overlapping
of cuts when mowing.
Lawn becomes matted.
Turbo signal has not
Ejection blocked
been detected
J + K .
Cutting height too low for
grass that is too high.
Pushing mower too fast.
Grass not dry.
Blade blunt.
Mulched grass
appearance is poor:
clumps, excessive
clippings, rough cut.
Mulching rule not
followed (cut max. 1/3 of
the grass height; the
height of the grass to be
cut must be lower than
10 cm)
Travel speed too fast.
Grass build-up under
deck.
Insufficient overlapping
of cuts when mowing.
Grass not dry.
Repairs to electrical machines must always be performed only by qualified electricians.
Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the
nearest authorized dealer. This applies in particular to appliances with electrical motors,
as when these are repaired they must always undergo an insulation protection test.
Your authorized dealer will also help you if you do not wish to perform any of the
maintenance work described here yourself.

18 TECHNICAL DATA

Remedy

Motor

Connect the plug C2 .
Check the fuse.
Get it checked by an
authorised workshop.
Set a higher cutting height I .
Machine tilts when starting it.

Mower

Clean the cutting chamber of
grass, ensure that the gap
between fan and housing is
kept clean (pull the plug
first!).
Get it checked by an
authorised workshop.
Have it checked by an
authorized dealer
Have it sharpened and
balanced by an authorized
dealer Q .
Adjust to higher cutting height
I .
Adjust mowing speed.
Tall grass conditions may

Sound power level

dictate that more overlapping
of cuts is required.
A lawn scarifier can remedy
the problem considerably

Sound pressure level

Empty the grass collector L .
Adjust to higher cutting height
I .

Vibrations

Adjust mowing speed.
Let grass dry.
Have it sharpened and
balanced by an authorized
dealer.

19 ORIGINAL SPARE PARTS

Adjust to higher cutting height
I .
Convert mower to rear
discharge U2 + S1 and
mow grass first with higher
cutting setting.
Adjust travel speed.
Adjust to higher cutting height
I .
Declaration of Conformity
Tall grass conditions may
dictate that more overlapping
of cuts is required
Adjust to higher cutting height
I .
Let grass dry.
10
Motor
Connection voltage
Power
Motor speed
Housing
Cutting width
Cutting heights
Adjustable-height handlebar
Grass collector capacity
Weight
Length
Width
Height
Wheels front / rear
Bearing front
Bearing rear
Guaranteed sound power level;
measured according to 2000/14/EC
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871
Vibrations on the lawnmower's handlebar;
measured according to EN60335-2-77
Measuring inaccuracy; according to EN 12096
Conversion kit for mulching system
Roller bearing grease
Cutter bar
see the back, after the last language
Alternating current motor
230 V
1300 W
3000 min
Die-cast aluminium
360 mm
Central, 20, 28, 35, 45, 55, 70 mm
3-way
43 litres
22 kg
1265 mm
420 mm
980 mm
Ø 150 mm / Ø 175 mm
Cup-and-cone bearing
Cup-and-cone bearing
L = 92 dB(A)
wa
L = 80 dB(A)
pA
3 dB
a = 1 m/s
hW
0,5 m/s
SA504
SAA11300
For safety reasons, the cutter bar must
always be replaced by an authorised
workshop.
This workshop has the respective spare
part numbers for the cutter bar available.
-1
2
2