Using The Saw - EINHELL TE-CC 2025 UF Manual De Instrucciones

Sierra circular de mesa
Ocultar thumbs Ver también para TE-CC 2025 UF:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 85
(31) to the base frame.
Use the screws (e) and washers (d) to fasten
the machine to the base frame.
The base frame is fitted with an adjustable
rubber foot (13). You can use it to compensate
for small unevenness on the work surface.
6.3 Fitting and adjusting the splitter
(Fig. 6a, 9)
Danger! Pull out the power plug.
Set the blade (4) to max. cutting depth, move
to 0° position and lock in place.
Dismantle the saw blade guard (see 6.4).
Take out the table insert (see 6.5).
Undo the fastening screw (19).
Insert the splitter between the mounting plate
(29) and the splitter counter bearing (30).
The distance between the splitter and the
saw blade should be approx. 3-5 mm.
Retighten the fastening screw and fit the table
insert.
6.4 Fitting/removing the saw blade guard
(Fig. 6b)
Mount the saw blade guard on the splitter so
that the screw (15) fits through the hole (18)
in the splitter.
Do not tighten the screw too far – the blade
guard must be able to move freely.
To dismantle, proceed in reverse order.
Warning! The saw blade guard must always
be lowered over the workpiece before you
begin to cut.
6.5 Changing the table insert (Figure 7)
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
Remove the 1 countersunk head screws (17).
Take out the worn table insert (6).
To fit the replacement table insert, proceed in
reverse order.
6.6 Fitting/replacing the saw blade (Fig. 8)
Warning! Pull out the power plug.
Take out the table insert (see 6.5).
Undo the screw (36) by placing one open-
ended spanner on the nut and another open-
ended wrench on the outer flange (40) to
apply counter-pressure.
Turn the nut in the direction of rotation of the
saw blade
Remove the outer flange and remove the old
saw blade from the shaft and the inner flange.
Anl_TE_CC_2025_UF_SPK7.indb 27
Anl_TE_CC_2025_UF_SPK7.indb 27
GB
Clean the flanges before fitting the new saw
blade.
Fit the new saw blade by following the above
instructions in reverse and then retighten it.
Important! Check that the saw blade turns in
the correct direction. The cutting direction of
the teeth must point in the running direction,
meaning forwards.
Refit the table insert and the saw blade guard
(see 6.4, 6.5)
6.7 Connection for dust extractor (Fig. 2, 10)
The machine can be connected to a dust extrac-
tor (the extractor adapter set with suction hose is
not included and is available as an accessory):
Connect the dust extractor to the extractor
adapter (16).
Also, an extraction hose can be connected
to the saw blade guard. To do so, remove the
cap from the saw blade guard, then fit the
extraction hose.

7. Using the saw

7.1. ON/OFF switch (Fig. 1, 16)
To turn the saw on, press the green button
"I". Wait for the blade to reach its maximum
speed of rotation before commencing with the
cut.
To turn the machine off again, press the red
button "0".
The motor of this equipment is protected against
overload by an overload switch (41).
If the rated current is exceeded, the overload
switch (41) will shut down the equipment.
Let the equipment cool down for several minutes.
Press the overload switch.
Press the green button „I" to switch on the equip-
ment.
7.2. Cutting depth (Fig. 1)
Turn the hand crank (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
larger cutting depth
Turn clockwise:
smaller cutting depth
7.3. Parallel stop
- 27 -
04.10.2016 15:01:04
04.10.2016 15:01:04
Tabla de contenido
loading

Este manual también es adecuado para:

43.405.47

Tabla de contenido