Care And Maintenance; Danger Of Ffreezing; Pump Dismounting And Storing; Trouble Shooting - Metabo P 3300 S Manual De Instrucciones

1. Plug power cable in.
2. Check to see that the power indica-
tor (20) is illuminated.
3. Open discharge line.
Press the reset button (22). The
4.
pump will start running.

If there is no water pumped after
approx. 10 seconds the Hydromat
will turn off.Then press and hold the
(22)
reset button
emerges.

If no water emerges after approx. 3
minutes, check the suction line.

7. Care and Maintenance

A Danger!
Prior to all servicing:
1. Turn OFF.
2. Unplug.
3. Ensure that pressure is relieved
from the pump and connected
accessories.
Service and repair work other than
described here must be left to quali-
fied specialists.
7.1

Danger of Ffreezing

A
Caution!
Frost damages the pump and
accessories, as both always contain
water!

When there is danger of freezing,
dismount the pump and accessories
and store at a frost-free location
(see below).
7.2 Pump Dismounting and
Storing
1. Turn pump OFF and unplug.
2. Open pressure line (open tap or
spray nozzle) and drain water com-
pletely.
3. Drain pump completely; to do so
remove the drain plug from the
pump
4. Disconnect suction and pressure
lines from the pump.
5. Store pump in a frost-free location
(at least 5 °C).

8. Trouble Shooting

Danger!
A
Prior to all servicing:
1. Turn OFF.
2. Unplug.
3. Ensure that pressure is relieved
from the pump and connected
accessories.
8.1

Locating the Fault

Pump does not run:
 Pump not turned ON.
• Start pump
switch.
 Hydromat has cut out.
• Press the reset button. 
If no water is pumped after
approx. 10 seconds, press and
hold reset button until Water
emerges.
 No mains voltage.
• Check cables, plug, outlet and
until water
mains fuse.
 Mains voltage too low.
• Use only extension cables with
sufficient lead cross section (see
"Technical Specifications").
 Motor overheated, motor protection
relay tripped.
• After cooling off the pump will
start again.
• Ensure sufficient ventilation, keep
vent slots clear.
• Observe max. temperature of the
pumped medium.
 Motor hums but does not start.
• With the motor turned OFF, put
screwdriver or similar through the
fan cover's ventilation slots and
turn the fan.
 Pump blocked or out of order.
• Disassemble pump and clean.
• Clean diffusor, replace if neces-
sary.
• Clean impeller, replace if neces-
sary.
Pump does not prime correctly or
runs very noisily:
 Lack of water.
• Ensure there is a sufficient water
supply.
 Suction line leaky.
• Seal suction line, tighten screw
fittings.
 Suction head too high.
• Observe max. suction head.
• Install check valve, fill suction line
with water.
 Suction strainer (optional acces-
sory) blocked.
• Clean, replace if necessary.
 Check valve (optional accessory)
blocked.
• Clean, replace if necessary.
 Water leaks between motor and
pump, Duocone seal worn.
• Replace Duocone seal.
 Pump blocked or out of order.
• see above.
Pressure too low:
 Suction line leaky or too much suc-
tion head.
• see above.
 Pump blocked or out of order.
at the ON/OFF

9. Repairs

A
only be carried out by a qualified
electrician!
Electric tools in need of repair can be
sent to an authorized service center in
your country. See spare parts list for
address.
Please attach a description of the fault to
the electric tool.

10. Environmental Protection

The packaging material of the pump is
100 % recyclable.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.

11. Available Accessories

For this pump the following accessories
are available from your dealer.
3
are shown at the end of this manual.
A
B
C
D
E
F
G
ENGLISH
• see above.
Danger!
Repairs to electric tools must
Note: 
Illustrations and stock numbers
Pump Installation Package, 
(MSS 310 – HWA/P), complete with
double nipple, check valve, filter
short, washable filter cartridge, spi-
ral hose assembly 1 m, thread seal-
ing tape.
Pump Installation Package, 
(MSS 380 – HWW), complete with
double nipple, check valve, filter
short, washable filter cartridge, spi-
ral hose assembly 1 m, thread seal-
ing tape.
Pump Installation Package, 
(MSS 200 – HWW/P), complete
with double nipple, check valve, fil-
ter short, washable filter cartridge,
spiral hose assembly 1 m, thread
sealing tape.
Pump Installation Package, 
(MSS 1000 – HWA), complete with
double nipple, check valve, filter
short, washable filter cartridge, spi-
ral hose assembly 1 m, thread seal-
ing tape.
Filter (for garden pumps), 
1" connection, short, 
c/w washable synthetic material fil-
ter cartridge.
Filter (for domestic water systems), 
1" connection, short, 
c/w washable synthetic material fil-
ter cartridge.
Spiral Suction Hose 1" (standard)
1) 4 m, c/w quick release screw fit-
ting and strainer with foot valve;
15